Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM32K0E _57 Power Source / Network _059857 NETWORKING _0298527 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2324  Rear Door LH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2324 Rear Door LH ECU Communication Stop No communication between power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for rear LH door)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

DOOR R/L fuse



WIRING DIAGRAM

B457237E04
0.969,0.719 1.583,0.917 0.615,0.198 10 false LIN2 0.104,1.74 0.604,1.99 0.5,0.25 10 false MB 0.104,1.906 1.802,2.375 1.698,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 1.365,1.073 1.979,1.271 0.615,0.198 10 false 3H 1.365,1.229 2.99,1.656 1.625,0.427 10 false Instrument Panel Junction Block Assembly 1.396,0.531 1.615,0.719 0.219,0.188 10 false 16 2.99,0.531 3.26,0.719 0.271,0.188 10 false 25 3.573,0.531 3.844,0.719 0.271,0.188 10 false 9 3.802,0.719 4.417,0.917 0.615,0.198 10 false LIN 4.427,0.563 5.042,0.76 0.615,0.198 10 false B 4.229,1.281 4.844,1.479 0.615,0.198 10 false GND 4.677,0.469 4.948,0.656 0.271,0.188 10 false 2 4.677,1.188 4.948,1.375 0.271,0.188 10 false 1 4.698,0.708 5.5,0.958 0.802,0.25 10 false DOOR R/L 5.677,0.563 7.125,0.781 1.448,0.219 10 false from Auxiliary Battery 3.344,1.875 5.302,2.344 1.958,0.469 10 false Power Window Regulator Motor Assembly (for Rear LH Door) 3.344,1.708 4.177,1.958 0.833,0.25 10 false L2 0.917,3.083 2.823,3.333 1.906,0.25 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


B426689C13
2.083,1 2.417,1.25 0.333,0.25 5.5,0.75 5.833,1 0.333,0.25 2.198,2.156 2.198,1.573 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.156,1.052 2.469,1.25 0.313,0.198 10 false MB 5.583,0.802 5.896,1 0.313,0.198 10 false 3H 2.083,2.219 2.698,2.417 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3H-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door))

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door))
a.

Disconnect the L2 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
3H-25 - L2-9 (LIN) Power switch off Below 1 Ω
L2-9 (LIN) or 3H-25 - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L2-2 (B) - L2-1 (GND) Power Switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)
a.

Replace the power window regulator motor assembly (for rear LH door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2324 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)