Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0299417 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the hybrid vehicle control ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*):
·

A malfunction is detected in the communication or communication lines between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU).

·

The communication ID codes of the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) do not match.


·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the hybrid system and wait for 10 seconds. If there is a malfunction, the hybrid control system will stop (communication begins within 3 seconds of the hybrid control system start, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the hybrid system and wait for 10 seconds (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Hybrid control system start operation. ○ ○ ○
Malfunction Status A malfunction in the communication between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU). ○ - -
A malfunction in the communication lines between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU). - ○ -
A matching communication code cannot be verified during communication between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU). - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

B424447C01
5.313,1.74 5.771,1.938 0.458,0.198 10 false IMI 5.302,0.833 5.76,1.031 0.458,0.198 10 false IMO 5.5,1.406 5.958,1.604 0.458,0.198 10 false 12 V 5.021,1.74 5.615,2.094 0.594,0.354 10 false 22 5.021,0.833 5.479,1.031 0.458,0.198 10 false 23 5.438,2.948 6.844,3.531 1.406,0.583 10 false Hybrid Vehicle Control ECU Assembly 5.448,2.802 6.302,2.99 0.854,0.188 10 false F3 1.594,0.833 2.052,1.031 0.458,0.198 10 false EFII 1.521,1.74 1.979,1.938 0.458,0.198 10 false EFIO 1.167,0.167 1.625,0.365 0.458,0.198 10 false 12 V 1.979,0.833 2.438,1.031 0.458,0.198 10 false 3 1.99,1.74 2.448,1.938 0.458,0.198 10 false 4 0.313,2.771 1.167,2.958 0.854,0.188 10 false F21 0.313,2.938 1.896,3.323 1.583,0.385 10 false ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

When replacing the hybrid vehicle control ECU assembly or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279986 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMO)
2.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B427510C04
5.219,0.083 5.635,0.333 0.417,0.25 6,2.021 5.833,2.021 5.833,2.021 5.365,1.125 true 2.75,4.427 2.917,4.427 2.917,4.427 2.917,3.938 true 3.271,4.427 3.104,4.427 3.104,4.427 3.104,3.938 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.927,2.958 3.24,3.115 0.313,0.156 10 false *b 2.563,4.313 2.875,4.469 0.313,0.156 10 false *c 3.302,4.323 3.615,4.479 0.313,0.156 10 false *d 0.938,3.896 1.406,4.167 0.469,0.271 10 false GND 6.042,1.938 6.5,2.135 0.458,0.198 10 false IMO 5.354,0.115 5.792,0.354 0.438,0.24 10 false F3
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F3-23 (IMO) - Body ground Turn the power switch on (READY) 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)

B

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU)

C

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B427511C02
5.188,0.167 5.604,0.417 0.417,0.25 5.917,2.104 5.75,2.104 5.75,2.104 5.448,1.177 true 3.052,4.594 3.219,4.594 3.219,4.594 3.219,4.073 true 3.563,4.583 3.396,4.583 3.396,4.583 3.396,4.073 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 3.229,3.031 3.542,3.188 0.313,0.156 10 false *b 2.885,4.479 3.198,4.635 0.313,0.156 10 false *c 5.958,2.021 6.25,2.26 0.292,0.24 10 false IMI 5.323,0.208 5.646,0.448 0.323,0.24 10 false F3 3.573,4.49 3.865,4.729 0.292,0.24 10 false *d 0.875,4.031 1.292,4.24 0.417,0.208 10 false GND
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F3-22 (IMI) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the power switch on (IG).


b.

Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU)
a.

Disconnect the F3 hybrid vehicle control ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-23 (IMO) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-3 (EFII) - F3-23 (IMO) Always Below 1 Ω
F21-3 (EFII) or F3-23 (IMO) - Body ground Always 10 kΩ or higher
F21-4 (EFIO) - F3-22 (IMI) Always Below 1 Ω
F21-4 (EFIO) or F3-22 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Replace the hybrid vehicle control ECU assembly with a new one.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279986 is not output.



Result:
Proceed to
OK
NG



OK

END (HYBRID VEHICLE CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)