Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0299417 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) is stuck high, the hybrid vehicle control ECU assembly will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Wire harness or connector

·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU assembly


DTC output confirmation operation:

Turn the power switch on (IG) and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

B424448E19
0.5,1.729 0.958,1.927 0.458,0.198 10 false F21 0.5,1.875 2.073,2.323 1.573,0.448 10 false ID Code Box (Immobiliser Code ECU) 1.719,0.708 2.177,0.906 0.458,0.198 10 false EFIO 5.146,0.708 5.604,0.906 0.458,0.198 10 false IMI 5.25,1.74 6.323,1.958 1.073,0.219 10 false F3 5.24,1.896 6.625,2.354 1.385,0.458 10 false Hybrid Vehicle Control ECU Assembly 4.844,0.708 5.646,0.906 0.802,0.198 10 false 22 2.198,0.708 2.656,0.906 0.458,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

When replacing the hybrid vehicle control ECU assembly or ID code box (immobiliser code ECU), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A12 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch on (IG) and wait 10 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

If DTCs other than DTC B279A12 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
Only DTC B279A12 is output A
DTC B279A12 and other DTCs are output B



A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Disconnect the F3 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-4 (EFIO) - F3-22 (IMI) Always Below 1 Ω
F21-4 (EFIO) or F3-22 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Replace the hybrid vehicle control ECU assembly with a new one.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A12 is not output.



Result:
Proceed to
OK
NG



OK

END (HYBRID VEHICLE CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)