Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0299673 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT

a.
C365306C01
0.188,1 0.5,1.156 0.313,0.156 10 false *a 1.198,1.896 1.51,2.052 0.313,0.156 10 false *b 0.938,0.125 1.25,0.281 0.313,0.156 10 false *c 1.74,0.125 2.052,0.281 0.313,0.156 10 false *d
*a 5 m (16.4 ft.)
*b 6 m (19.7 ft.)
*c 4 m (13.1 ft.)
*d 2 m (6.56 ft.)
V100144

Do not place any metal objects in this area
V100155

Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area


Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.

HINT:

Metal objects with a height of 50 mm (1.97 in.) or less placed within the area shown in the illustration will not affect the adjustment.



b.

Check the levelness of the ground.

i.
C365307C01
1.5,0.604 1.813,0.76 0.313,0.156 10 false *a
*a 3 m (9.84 ft.)
V100155

Levelness Check Point


Check the levelness of the ground at the 3 points shown in the illustration.


ii.

Place the level on each levelness check point and check that the air bubble of the level is centered.

E344401



c.

Adjust the tire inflation pressure to the specified pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


d.

Clean the front emblem or millimeter wave radar sensor assembly.


e.

Visually inspect the front of the vehicle.

HINT:

Confirm that there is no damage or deformation.



f.

Visually inspect the front bumper assembly, radiator grill and stays.

HINT:

Confirm that there is no damage or deformation.



Hide 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY

a.
C320141C03
1.448,0.615 1.938,0.615 false 1.708,0.865 1.927,0.615 false 1.969,0.542 2.281,0.74 0.313,0.198 10 false *a
*a SST (reflector)


Adjust SST (reflector) height.

i.

Adjust SST (reflector) so that the center of SST (reflector) is the same height as the millimeter wave radar sensor.

HINT:

Make sure to align the center of SST (reflector) with the millimeter wave radar sensor (the center of the emblem).


Reference Value:

771 mm (2.53 ft.)


SST
09870-60000  (09870-60010)
09870-60040  



b.

Place SST (reflector).

i.

Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.

C365298C02
2.635,2.583 3,2.417 false 4.875,1.583 5.573,1.25 true 3.042,2.479 3.406,2.479 false 4.865,0.583 5.573,0.917 true 4.583,0.479 4.771,0.656 0.188,0.177 10 true *a 2.427,2.5 2.74,2.656 0.313,0.156 10 false *b 4.573,1.5 4.781,1.698 0.208,0.198 10 true *c 3.479,2.385 3.729,2.635 0.25,0.25 10 false A
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



ii.

Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.

C365299C02
3.75,2.417 4,2.583 false 3.385,2.49 3.719,2.49 false 1,1.167 1.604,1.417 true 1.271,0.833 1.604,0.833 true 0.958,0.729 1.188,0.885 0.229,0.156 10 true *a 4.063,2.5 4.375,2.656 0.313,0.156 10 false *b 0.688,1.052 0.917,1.208 0.229,0.156 10 true *c 3.208,2.396 3.542,2.646 0.333,0.25 10 false B
*a String *b Weight
*c Center - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Using tape and a string, create a line that connects point B to point A and extends at least 3000 mm (9.84 ft.) beyond the front center point of the vehicle.

C365308C01
6.438,2.083 6.438,1.75 false 1.083,1.99 1.083,1.656 false 0.667,1.75 0.667,2.083 false 1.021,2 1.333,2.156 0.313,0.156 10 false *a 0.604,2.094 0.917,2.25 0.313,0.156 10 false *b 2.417,0.302 2.729,0.458 0.313,0.156 10 false *c 6.229,1.448 6.479,1.615 0.25,0.167 10 false A 3.208,1.438 3.458,1.604 0.25,0.167 10 false B 1.406,1.458 1.656,1.625 0.25,0.167 10 false C 6.365,2.083 6.677,2.24 0.313,0.156 10 false *b
*a String *b Tape
*c 3000 mm (9.84 ft.) - -


HINT:
·

Make sure the string is taut when securing it with tape.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




iv.

Mark point C (SST (reflector) placement position) at a position 3000 mm (9.84 ft.) from point B.


v.

Place SST (reflector) at point C.



c.

Front Beam Axis Adjustment:

NOTICE:
·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not turn off the GTS or power switch.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Close all of the doors.



i.

Connect the GTS to the DLC3.


ii.

Turn the power switch to on (IG).


iii.

Turn the GTS on and turn the cruise control system on using the cruise control main switch (ON/OFF button).


iv.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Adjustment
50005 220 4404

v.

According to the display on the GTS, press "Next".


vi.

Perform the adjustment according to the display on the GTS.

NOTICE:

If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.


Error No. Error Description Cause of Error Action to be Taken
1 No target abnormality
·

The reflector is placed incorrectly.

·

The front emblem or millimeter wave radar sensor assembly is covered by dirt or snow.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
Clean the front emblem or millimeter wave radar sensor assembly.
Check the installation condition of the front bumper assembly and radiator grill.
2 Target distance abnormality
·

The reflector is placed incorrectly.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
3 Plural targets abnormality
·

There is a reflective object near the reflector.

·

A person entered the adjustment area.


Remove any reflective objects.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
4 Target move abnormality
·

The reflector was moved out of position or shaking during the adjustment due to wind.

·

A person entered the adjustment area.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b)Place the reflector)
Perform adjustment in an area with no wind.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
6 Target angle abnormality
·

The reflector is placed incorrectly.

·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b)Place the reflector)
Check the condition of the sensor, radiator grill and front bumper assembly.
7 Radar abnormality
·

Millimeter wave radar sensor assembly learning in progress. *1

·

Operation of the millimeter wave radar sensor assembly is abnormal.


·

Clear DTCs.

·

Check for DTCs.

(Click here)


8 Radar dirtiness
·

There is dirt on the front emblem or millimeter wave radar sensor assembly.


Clean the front emblem or millimeter wave radar sensor assembly.
9 Temperature abnormality
·

The temperature around the millimeter wave radar sensor assembly is too high.


Wait until the temperature drops to the operable range (-30 to 50°C).
10 Voltage abnormality
·

IG power source voltage is outside the operable range of the millimeter wave radar sensor assembly.


Check the battery voltage (specified condition: 11 to 14 V).
(Click here)
11 External communication abnormality
·

CAN communication between DSS and the millimeter wave radar sensor assembly is abnormal.


Check the condition of the connectors.
12 Radar axis aiming failure upward
·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (upward).


Check the installation condition of the front bumper assembly and radiator grill.
13 Radar axis aiming failure downward
·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (downward).


Check the installation condition of the front bumper assembly and radiator grill.
14 Vehicle speed abnormality
·

The vehicle is not stationary.


Ensure that the vehicle remains stationary.
15 Other
·

A mode change error occurred.

·

Operation of the yaw rate sensor is abnormal.

·

The vehicle is shaking.


Perform adjustment again. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (c) Front Beam Axis Adjustment)
Check for DTCs.
(Click here)
Ensure that the vehicle remains stationary.

*1: When millimeter wave radar sensor learning is in progress, clear the DTCs and perform beam axis alignment again.


vii.

Press the "Exit" button to finish front beam axis adjustment.



d.

Front Beam Axis Misalignment Reading:

NOTICE:
·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not turn off the GTS or power switch.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Close all of the doors.



i.

Enter the following menus: Body Electrical > Pre-Collision 2 > Utility.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 4405

ii.

According to the display on the GTS, press "Next".


iii.

Perform the adjustment according to the display on the GTS.

Specified Condition:
Vertical -0.4 to 0.4 deg
Horizontal -0.3 to 0.3 deg


NOTICE:

If the result is not as specified, perform beam axis adjustment again.




e.

Front Beam Axis Offset Reading:

i.

Enter the following menus: Body Electrical > Pre-Collision 2 > Utility.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 4406

ii.

According to the display on the GTS, press "Next".


iii.

Perform the adjustment according to the display on the GTS.

Specified Condition:
Vertical learning value 0 deg
Horizontal learning value 0 deg


NOTICE:

If the result is not as specified, perform beam axis adjustment again.



iv.

Turn the power switch off.


v.

Disconnect the GTS from the DLC3.