Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT › 2016.10–2019.09
RM32K0E _53 Suspension _061340 FRONT SUSPENSION _0299694 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point
·

Lane departure alert system (w/ Steering Control)

·

Simple intelligent parking assist system*1

·

Toyota parking assist sensor system*1

·

Pre-collision system


(Click here)
Initialize back door lock Power door lock control system (Click here)


NOTICE:
·

When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C345012

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C345013

Remove the cotter pin.


c.

Remove the nut.


d.
C345014C02
0.938,1.094 0.938,0.24 true 1.073,1.135 1.073,0.24 1.073,0.24 0.844,0.24 false 3.083,0.917 3.396,1.073 0.313,0.156 10 false *a 0.542,0.156 1,0.354 0.458,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C345015C02
1.698,1.615 2.698,1.615 false 2.219,2.417 2.635,1.938 2.635,1.938 2.74,1.938 true 1.01,4.365 1.125,4.365 1.125,4.365 1.333,3.99 false 1.542,1.271 1.99,1.271 false 0.833,4.271 1.146,4.427 0.313,0.156 10 false *a 2.438,0.656 2.75,0.813 0.313,0.156 10 false *b 1.365,1.167 1.677,1.323 0.313,0.156 10 false *c 2.792,1.854 3.104,2.01 0.313,0.156 10 false *d 2.438,0.281 2.75,0.438 0.313,0.156 10 false *b 2.76,1.531 3.073,1.688 0.313,0.156 10 false SST 2.208,3.49 2.521,3.646 0.313,0.156 10 false A 2.208,3.771 2.521,3.927 0.313,0.156 10 false B
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

NOTICE:
·

Apply molybdenum grease to the threads and end of the SST bolt.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.