The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
*1 w/ Height Control Sensor
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.REMOVE REAR WHEEL
17430
2.REMOVE TAIL EXHAUST PIPE ASSEMBLY
58166
3.REMOVE FRONT FLOOR COVER LH
58165B
4.REMOVE FRONT FLOOR COVER RH
Perform the same procedure as for the LH side.
57628C
5.REMOVE REAR FLOOR SIDE MEMBER COVER LH
57627A
6.REMOVE REAR FLOOR SIDE MEMBER COVER RH
47319F
7.SEPARATE REAR FLEXIBLE HOSE LH
Remove the bolt and separate the rear flexible hose LH from the flexible hose bracket.
47318F
8.SEPARATE REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
89408C
9.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
48840A
10.REMOVE REAR STABILIZER LINK ASSEMBLY LH
48830D
11.REMOVE REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48812
12.REMOVE REAR STABILIZER BAR
48231B
13.REMOVE REAR COIL SPRING LH
48231A
14.REMOVE REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48258C
15.REMOVE REAR LOWER COIL SPRING INSULATOR LH
48258B
16.REMOVE REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48740F
17.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
18.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
19.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
20.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
21.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH
Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48770A
22.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH
Use the same procedure as for the LH side.
51206A
23.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
w/ Height Control Sensor:
Disengage the clamp to separate the height control sensor wire harness.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Remove the 2 bolts and 2 nuts.
Slowly lower the rear suspension member sub-assembly.
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
48790
24.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
25.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
51249A
26.REMOVE REAR SUSPENSION MEMBER DAMPER
Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.
51284
27.REMOVE REAR SUSPENSION MEMBER HOLE COVER
| *a | for LH Side |
| *b | for RH Side |
Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.
28.REMOVE HOLE PLUG
Remove the 7 hole plugs from the rear suspension member sub-assembly as shown in the illustration.