Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300402 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for the LHD vehicles.



PROCEDURE

Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.
E339399

Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.


b.

Engage the clamp.


c.

Engage the claws to install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case.

E339398


d.

Install the 2 screws.


Hide 88515 3.INSTALL COOLER EXPANSION VALVE

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



b.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



c.
E339397

Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


d.
E339396

Install the grommet.


Hide 87107A 4.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E339395C02
0,0 0,0 false
V113147

Install in this Direction


Install the heater radiator unit sub-assembly as shown in the illustration.


Hide 87124B 5.INSTALL HEATER CLAMP

a.
E339393

Engage the claws to install the heater clamp.


Hide 88897M 6.INSTALL HEATER PIPE GROMMET

a.
E339392

Install the heater grommet.


Hide 87050C 7.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.

Align each gear on the air conditioner radiator assembly as shown in the illustration, and then check that the gears of the No. 1 air conditioning radiator damper servo sub-assembly arealigned as shown in the illustration.

E339385C01
5.896,1.052 4.313,0.854 4.313,0.854 5.083,1.26 true 2.479,1.906 3.438,0.875 3.438,0.875 1.958,1.635 true 3.479,0.74 3.792,0.896 0.313,0.156 10 false *a 4.115,0.729 4.427,0.885 0.313,0.156 10 false *a
*a Reference Point - -



b.

Using the reference points, install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.

E339386C01
5.167,0.854 5.167,1.24 5.167,1.24 5.292,0.917 true 5.083,1.271 5.396,1.427 0.313,0.156 10 false *a
*a Reference Point - -



Hide 88539J 8.INSTALL DRAIN COOLER HOSE

a.
E339336C02
1.385,1.688 2.094,2.51 true 2.167,2.469 3,2.021 true 1.219,1.573 1.531,1.729 0.313,0.156 10 false *a 3.031,1.917 3.344,2.073 0.313,0.156 10 false *b
*a Hose Notch
*b Rib


Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.


Hide 88482A 9.INSTALL COVER

a.
I113812

Engage the claws to install the cover.


Hide 82210K 10.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

Engage the clamps.

E339334


b.

Connect each connector to install the air conditioning harness assembly.


Hide 88650N 11.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

a.
E337298C02
0,0 0,0 false
V113147

Install in this Direction


for LHD:

i.

Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.


ii.

Install the air conditioning amplifier assembly with the screw.


iii.

Connect the connector.



b.
E337295C02
0,0 0,0 false
V113147

Install in this Direction


for RHD:

i.

Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.


ii.

Install the air conditioning amplifier assembly with the screw.


iii.

Connect the connector.



Hide 87710G 12.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

a.
E337341C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guide to install the quick heater assembly as shown in the illustration.


Hide 87114L 13.INSTALL NO. 2 HEATER COVER (w/ PTC Heater)

a.
E337339

Engage the claw and guide to install the No. 2 heater cover.


b.

Install the screw.


Hide 87114B 14.INSTALL HEATER COVER (w/o PTC Heater)

a.
E339333C02
0,0 0,0 false
V113147

Install in this Direction


Install the heater cover with the screw as shown in the illustration.


Hide 87130D 15.INSTALL BLOWER ASSEMBLY

Hide 82143 16.INSTALL NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)

a.
E339331

Engage the clamps to install the No. 3 instrument panel wire.


b.

Connect the 2 connectors.


Hide 88505 17.INSTALL AIR CONDITIONING DUCT SUB-ASSEMBLY

a.
E339330

Engage the claws to install the air conditioning duct sub-assembly.


Hide 87211A 18.INSTALL NO. 2 AIR DUCT (for LHD)

a.
E339329

Engage the claws to remove the No. 2 air duct.


b.

Install the screw.


Hide 87211 19.INSTALL NO. 1 AIR DUCT (for RHD)

a.
E337805

Engage the claws to remove the No. 1 air duct.


b.

Install the screw.