Use the same procedure for RHD and LHD vehicles.
The following procedure is for the LHD vehicles.
55990B
1.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
Engage the claws to install the lower defroster nozzle assembly.
2.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
|
Install in this Direction | - | - |
Connect 2 connectors.
Engage the clamps.
Install the 5 bolts.
Temporarily install the nut.
Install the 2 bolts.
88539J
4.CONNECT DRAIN COOLER HOSE
| *1 | Cooler Unit Drain Hose Grommet |
Connect the drain cooler hose.
If the cooler unit drain hose grommet is disconnected from the vehicle body while connecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.
82141
5.INSTALL INSTRUMENT PANEL WIRE
for LHD:
Engage clamps and hook to connect the instrument panel wire.
| *a | Clamp | *b | Hook |
Install the instrument panel junction block assembly with main body ECU with the bolt and nut.
Install the 4 ground wires with the 4 bolts.
Install the bolt and screw.
Connect each connector.
for RHD:
Engage clamps and hook to connect the instrument panel wire.
| *a | Clamp | *b | Hook |
Install the instrument panel junction block assembly with main body ECU with the bolt and nut.
Install the 2 nuts A.
Install the 4 ground wires with the 4 bolts.
Install the bolt and screw.
Connect each connector.
55308B
6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.
Engage the claws and clamps.
55307C
7.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
for LHD:
Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Install the ground wire with the bolt.
Engage the clamps to connect the wire harness.
for RHD:
Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Install the ground wire with the bolt.
Engage the clamps to connect the wire harness.
55306A
8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
for LHD:
Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Engage the clamps to connect the wire harness.
for RHD:
Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Engage the clamps to connect the wire harness.
w/ PTC Heater:
Install the bolt to connect the ground wire.
Install the relay block assembly with the 2 nuts.
9.INSTALL AIR CONDITIONER UNIT ASSEMBLY
for LHD:
Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.
for RHD:
Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.
87212
10.INSTALL REAR NO. 1 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 1 air duct.
87212F
11.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 2 air duct as shown in the illustration.
87212G
12.INSTALL REAR NO. 3 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 3 air duct as shown in the illustration.
87212H
13.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 4 air duct as shown in the illustration.
|
Install in this Direction |
Install the front floor carpet assembly to its original position as shown in the illustration.
Engage the clamps.
Install the clip.
Install the 2 front floor carpet clips.
87212J
14.INSTALL REAR NO. 5 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 5 air duct as shown in the illustration.
87212K
15.INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Duct)
|
Install in this Direction |
Engage the claws to install the rear No. 6 air duct as shown in the illustration.
55215D
16.INSTALL NO. 3 DASH PANEL INSULATOR PAD
Engage the clips to install the No. 3 dash panel insulator pad.
|
Install in this Direction |
Install the front floor carpet assembly to its original position as shown in the illustration.
Engage the clamps.
Install the clip.
Install the 2 front floor carpet clips.
88625Q
17.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Connect the aspirator and connector to install the cooler thermistor (room temperature sensor).
82877
18.INSTALL ECU INTEGRATION BOX RH (for LHD)
82878
19.INSTALL ECU INTEGRATION BOX LH (for RHD)
89340A
20.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)
85940
21.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY
22.INSTALL STEERING COLUMN ASSEMBLY
55401E
23.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
24.INSTALL FRONT SEAT ASSEMBLY LH
25.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
88716A
26.CONNECT COOLER REFRIGERANT LIQUID PIPE A
Remove the vinyl tape from the cooler refrigerant liquid pipe A.
Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.
ND-OIL 11 or equivalent
Install the O-ring to the cooler refrigerant liquid pipe A.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the cooler refrigerant liquid pipe A.
88707
27.CONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the vinyl tape from the suction pipe sub-assembly.
Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.
ND-OIL 11 or equivalent
Install the O-ring to the suction pipe sub-assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction pipe sub-assembly.
Rotate the hook connector as shown in the illustration.
Insert the hose joint into the fitting hole securely and install the bolt.
87245
28.CONNECT INLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (White) |
| *c | Clip Installation Angle (120°) |
Connect the inlet heater water hose with the marking (pink) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
87246
29.CONNECT OUTLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (White) |
| *c | Clip Installation Angle (120°) |
Connect the outlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the outlet heater water hose.
55701J
30.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
31.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
55735C
32.INSTALL COWL BODY MOUNTING REINFORCEMENT RH
55736D
33.INSTALL COWL BODY MOUNTING REINFORCEMENT LH
55735A
34.INSTALL WATER GUARD PLATE LH
55737B
35.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
36.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
37.ADD ENGINE COOLANT
38.INSPECT FOR COOLANT LEAK
39. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
40.WARM UP COMPRESSOR
41.INSPECT FOR REFRIGERANT LEAK
42. INITIALIZATION SERVO MOTOR