Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300406 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88460 1.INSTALL COOLER CONDENSER ASSEMBLY

a.
I112512C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.


HINT:

If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz)


Compressor Oil:

ND-OIL 11 or equivalent



Hide 88707 2.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the open ends of the cooler condenser assembly and suction pipe sub-assembly.


b.
E253149C03
2.135,1.458 2.135,1.823 false 1.219,0.927 0.594,1.167 0.594,1.167 1.229,1.396 false 1.458,1.583 1.458,1.844 false 2.083,1.875 2.354,2.156 0.271,0.281 10 false *1 1.385,1.875 1.635,2.115 0.25,0.24 10 false *2 0.365,1.063 0.635,1.344 0.271,0.281 10 false *a
*1 Air Conditioner Tube and Accessory Assembly
*2 Piping Clamp
*a Groove


Install a new piping clamp to the suction pipe sub-assembly.

NOTICE:
·

Securely engage the inside step of the piping clamp in the suction pipe sub-assembly groove.

·

Do not widen the opening of the piping clamp more than the diameter of the suction pipe sub-assembly when installing it.

·

Do not install the piping clamp with the large diameter section in the wrong direction.




c.

Thoroughly coat 2 new O-rings and the contact surface of the suction pipe sub-assembly with compressor oil.

Compressor Oil:

ND-OIL 11 or equivalent



d.

Install the 2 O-rings to the suction pipe sub-assembly.

NOTICE:

Do not let foreign matter adhere to the O-rings or O-ring seals.



e.

Engage the cooler condenser assembly and suction pipe sub-assembly.

E336870C02
5.323,2.5 5.708,2.219 false 5.771,2.146 6.083,2.302 0.313,0.156 10 false *a
*a Large Diameter Section of Piping Clamp - -


NOTICE:

Engage the parts by holding the pipe, not the piping clamp.



f.

Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.

HINT:
·

When inserting, make sure that a click sound is heard.

·

Check that the suction pipe sub-assembly is securely inserted by pulling it.




Hide 88703 3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.


d.

Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 53019B 4.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)

Hide 16593B 5.INSTALL NO. 1 RADIATOR AIR GUIDE RH

Hide 16595B 6.INSTALL NO. 1 RADIATOR AIR GUIDE LH

Hide 52131A 7.INSTALL FRONT BUMPER REINFORCEMENT

Hide 52611 8.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide 16594 9.INSTALL NO. 2 RADIATOR AIR GUIDE

Hide 53205 10.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 17752 11.INSTALL NO. 2 AIR CLEANER INLET

Hide 53510 12.INSTALL HOOD LOCK ASSEMBLY

Hide 16561C 14.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53117C 15.INSTALL NO. 1 RADIATOR GRILLE RETAINER

Hide 52021B 16.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly to the vehicle with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17.INSTALL HEADLIGHT ASSEMBLY LH (for Halogen Headlight)

Hide 18.INSTALL HEADLIGHT ASSEMBLY LH (for LED Headlight)

Hide 19.INSTALL HEADLIGHT ASSEMBLY RH (for Halogen Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 20.INSTALL HEADLIGHT ASSEMBLY RH (for LED Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 21.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 53301 24.ADJUST HOOD SUB-ASSEMBLY