Home › Engine / Hybrid System › 2ZR-FXE (COOLING) › RADIATOR › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _060780 2ZR-FXE COOLING _0298030 RADIATOR A

2ZR-FXE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install the 2 O-ring to the radiator drain cock plug.

NOTICE:

Replace the O-ring if it is damaged.



b.

Install the 2 radiator drain cock plug.


Hide 16533C 2.INSTALL RADIATOR SUPPORT GROMMET

a.

Install the 2 radiator support grommets to the radiator assembly.


Hide 16523A 3.INSTALL RADIATOR SUPPORT CUSHION

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16400 4.INSTALL RADIATOR ASSEMBLY

a.

Engage the 2 guides.


b.

Engage the 2 claws to install the fan shroud assembly to the radiator assembly.

NOTICE:

Do not damage the radiator assembly when installing the fan shroud assembly.



c.

Install the radiator assembly with the fan shroud assembly to the vehicle body.


Hide 88460 5.INSTALL COOLER CONDENSER ASSEMBLY

Hide 88707 6.CONNECT SUCTION PIPE SUB-ASSEMBLY

Hide 88703 7.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 53019B 8.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)

Hide 53398A 9.INSTALL RADIATOR LOWER SEAL LH (w/ Grille Shutter)

Hide 53398A 10.INSTALL RADIATOR LOWER SEAL RH (w/ Grille Shutter)

Hide 16595B 11.INSTALL NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 12.INSTALL NO. 1 RADIATOR AIR GUIDE RH

Hide 52131A 13.INSTALL FRONT BUMPER REINFORCEMENT

Hide 52611 14.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide G92A0A 15.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.

Engage the 2 claws to install the inverter reserve tank assembly to the fan shroud assembly.


b.

Engage the clamp to connect the inlet hybrid water pump hose to the fan shroud assembly.


Hide G922C 16.CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

a.

Connect the outlet No. 1 inverter cooling hose to the radiator assembly and slide the clip to secure it.


Hide 16572D 17.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.


Hide 16571C 18.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the radiator assembly and slide the clip to secure it.


Hide G922AA 19.CONNECT INLET NO. 1 INVERTER COOLING HOSE

a.

Connect the inlet No. 1 inverter cooling hose to the radiator assembly and slide the clip to secure it.


Hide G922H 20.CONNECT INLET HYBRID RADIATOR HOSE

a.

Connect the inlet hybrid radiator hose to the radiator assembly and slide the clip to secure it.


b.

Engage the clamp to connect the inlet hybrid radiator hose to the fan shroud assembly.


Hide 16264 21.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the radiator assembly and slide the clip to secure it.


b.

Engage the 4 clamps.


Hide 16261 22.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the radiator assembly and slide the clip to secure it.


Hide 16594 23.INSTALL NO. 2 RADIATOR AIR GUIDE

a.

Engage the 5 claws to install the No. 2 radiator air guide to the radiator assembly.


Hide 53205 24.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Install the upper radiator support sub-assembly together with hood lock support sub-assembly to the vehicle with the 5 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Connect the cooling fan motor RH connector and cooling fan motor LH connector.


c.

Engage the 12 clamps to connect the wire harness to the upper radiator support sub-assembly and fan shroud assembly.


d.

Engage the 3 clamps to connect the wire harness to the horn and hood lock support assembly.


e.

Engage the clamp to connect the hood control cable sub-assembly to the upper radiator support sub-assembly.


Hide 17752 25.INSTALL NO. 2 AIR CLEANER INLET

Hide 53510 26.INSTALL HOOD LOCK ASSEMBLY

Hide 16561C 28.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53117C 29.INSTALL NO. 1 RADIATOR GRILLE RETAINER

Hide 52021B 30.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly to the vehicle with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide G9040 31.INSTALL INVERTER WATER PUMP ASSEMBLY

Hide 81175 32.INSTALL HEADLAMP UNIT ASSEMBLY LH

Hide 81135 33.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 34.ADD ENGINE COOLANT (for Engine)

Hide 35.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 36.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51441 37.INSTALL NO. 1 ENGINE UNDER COVER