Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300415 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I112557

When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 110 to 125 cc (3.8 to 4.2 fl. oz)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.




Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.
I112556N01
1.531,1.99 1.698,2.156 0.167,0.167 10 false 1 0.927,1.833 1.083,2.031 0.156,0.198 10 false 2 1.042,0.188 1.198,0.385 0.156,0.198 10 false 3

Temporarily install the compressor with motor assembly with the 3 bolts.


b.

Tighten the 3 bolts and install the cooler compressor with motor assembly in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.
I112558N01
1.875,2.594 2.031,2.792 0.156,0.198 10 true A 2.427,3 2.583,3.198 0.156,0.198 10 true B

Connect the connector B.


d.

Remove the protective tape wrapped around connector A, and as shown in the illustration, connect connector A and lower the green lock to lock it securely.

CAUTION:

Make sure to wear insulating gloves.


NOTICE:

Make sure that the connector is connected securely.



Hide 88704 3.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly and compressor with motor assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction hose sub-assembly to the with motor compressor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88703 4.INSTALL DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly and compressor with motor assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the discharge hose sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the discharge hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 51441 5.INSTALL NO. 1 ENGINE UNDER COVER

Hide 7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT