The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
1.INSTALL ENGINE HANGERS
2.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Remove the engine assembly from the engine stand.
13405
3.INSTALL FLYWHEEL SUB-ASSEMBLY
31270
4.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
5.INSTALL ENGINE ASSEMBLY
82121
6.INSTALL ENGINE WIRE
Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.
11363A
7.INSTALL FLYWHEEL HOUSING SIDE COVER
28193
8.INSTALL STARTER HOLE INSULATOR
88370
9.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
12305
10.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.
Install the 2 bolts and nut in the order shown in the illustration.
Connect the air conditioner tube and accessory assembly to the engine mounting insulator sub-assembly RH with the bolt and nut.
Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle body with the 2 bolts.
12372A
11.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator LH to the vehicle.
Install the 4 bolts and nut in the order shown in the illustration.
12.REMOVE ENGINE HANGER
13.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket with the bolt.
Engage the 3 clamps.
14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads of bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the No. 2 engine mounting stay LH with the bolt.
Install the engine mounting insulator LH to the hybrid vehicle transaxle assembly with the 3 bolts and nut.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.
51108A
15.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
17.INSTALL FRONT DRIVE SHAFT ASSEMBLY
17410
18.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
57533B
19.INSTALL FRONT FLOOR CENTER BRACE
58166
20.INSTALL FRONT FLOOR COVER LH
58165B
21.INSTALL FRONT FLOOR COVER RH
Use the same procedure as for the LH side.
45025D
22.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
23.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
24.INSTALL COLUMN HOLE COVER SILENCER SHEET
82123
25.CONNECT NO. 3 ENGINE WIRE
| *a | Bolt (A) |
| *b | Bolt (B) |
Connect the No. 3 engine wire to hybrid vehicle transaxle assembly with the 2 bolts.
Engage the clamp.
88704
26.CONNECT SUCTION HOSE SUB-ASSEMBLY
88703
27.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
G922F
28.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
Connect the outlet No. 1 hybrid water pump hose to the motor cooling cooler and slide the clip to secure it.
G922H
29.CONNECT INLET HYBRID RADIATOR HOSE
Connect the inlet hybrid radiator hose to the motor cooling cooler and slide the clip to secure it.
23901
30.CONNECT FUEL TUBE SUB-ASSEMBLY
23826
31.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the fuel vapor feed pipe and slide the clip to secure it.
87245A
32.CONNECT INLET HEATER WATER HOSE A
Connect the inlet heater water hose A to the EGR pipe with cooler sub-assembly and slide the clip to secure it.
87246
33.CONNECT OUTLET HEATER WATER HOSE
Connect the outlet heater water hose to the No. 1 water by-pass pipe and slide the clip to secure it.
16572D
34.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.
16573B
35.CONNECT NO. 3 RADIATOR HOSE
Connect the No. 3 radiator hose to the water outlet and slide the clip to secure it.
Install the 2 bolts to the hybrid vehicle transaxle assembly.
33820B
36.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the transmission control cable assembly to the cylinder head cover sub-assembly with the bolt.
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Install the transmission control cable assembly to the control shaft lever with the nut.
G9200
37.INSTALL INVERTER WITH CONVERTER ASSEMBLY
17751
38.INSTALL NO. 1 AIR CLEANER INLET
17771A
39.INSTALL AIR CLEANER BRACKET
17701
40.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
41.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
22210
42.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17752
43.INSTALL NO. 2 AIR CLEANER INLET
53141F
44.INSTALL RADIATOR COVER
16296
45.CONNECT NO. 8 WATER BY-PASS HOSE
Connect the No. 8 water by-pass hose to the No. 2 water by-pass hose assembly and slide the clip to secure it.
46.ADD ENGINE OIL
47.ADD HYBRID TRANSAXLE FLUID
48.ADD ENGINE COOLANT (for Engine)
49.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
50.CHECK ENGINE OIL LEVEL
51.INSPECT HYBRID TRANSAXLE FLUID
52.INSPECT SHIFT LEVER POSITION
53.ADJUST SHIFT LEVER POSITION
54.INSPECT FOR COOLANT LEAK (for Inverter)
55.INSPECT FOR COOLANT LEAK (for Engine)
56.WARM UP COMPRESSOR
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).
57.INSPECT FOR REFRIGERANT LEAK
58.INSPECT FOR FUEL LEAK
59.INSPECT FOR OIL LEAK
60.INSPECT FOR EXHAUST GAS LEAK
51444A
61.INSTALL REAR ENGINE UNDER COVER LH
Install the rear engine under cover LH to the vehicle with the 6 clips.
51443C
62.INSTALL REAR ENGINE UNDER COVER RH
Install the rear engine under cover RH to the vehicle with the 6 clips.
51441
63.INSTALL NO. 1 ENGINE UNDER COVER
| *1 | Bolt |
Install the No. 1 engine under cover to the vehicle with the 4 bolts, 4 screws and 4 clips.
64.INSTALL FRONT WHEELS
65.INSPECT IGNITION TIMING
66.INSPECT ENGINE IDLE SPEED
67.INSPECT CO/HC
68.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
69.CHECK SPEED SENSOR SIGNAL