Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1475  A/C Inverter Cooling / Heating System Malfunction  


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.

If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1475 A/C Inverter Cooling / Heating System Malfunction
Any of the following conditions is met:
·

A/C inverter temperature outside specified range (temperature too high)

·

There is an open to ground in temperature sensor circuit

·

There is a Short to ground in temperature sensor circuit


·

Cooling fan system

·

Refrigerant volume

·

Compressor with motor assembly

·

CAN communication system


Memorized

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (READY) ○ ○ ○
Malfunction Status Temperature of the A/C inverter is outside the specified range (temperature is too high) ○ - -
There is an open to ground in the temperature sensor circuit - ○ -
There is a short to ground in the temperature sensor circuit - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks.

·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Engine Cooling Fan Control electric cooling fan motor OFF/Low/High Perform this test when the following conditions are met:
·

Power switch is on (IG)

·

Engine is stopped

·

Shift lever in P


Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan
50004 372 26
OK:

Electric cooling fan operates smoothly.



Result:
Proceed to
OK
NG



OK

3.CHECK REFRIGERANT PRESSURE

NG

3.CHECK REFRIGERANT PRESSURE

b.

Turn the power switch on (READY).


c.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Item Condition
Vehicle doors Fully open
Temperature setting MAX COLD
Blower speed HI
A/C switch On
Recirculation/fresh switch RECIRCULATION
Interior temperature 25 to 35°C (77 to 95°F)



Standard Pressure:
Low pressure side:

0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1.37 to 1.57 MPa (14 to 16 kgf/cm2, 199 to 228 psi)


Result:
Proceed to
OK
NG



OK

4.READ OUTPUT DTC (DTC B1475)

NG

4.READ OUTPUT DTC (DTC B1475)
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Turn the power switch on (READY).


c.

Prepare the vehicle according to the table below.

Item Condition
Blower speed HI
A/C switch On
Temperature setting MAX COLD


d.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1475 is not output (normal) A
DTC B1475 is output B


NOTICE:

If the engine idles continuously when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.



A

SYSTEM IS OK

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY