Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14B9  Open in Ion Generator Circuit  


DESCRIPTION

The ion generator sub-assembly operates when both the ion generator switch and the blower switch are on. The air conditioning amplifier assembly sends a drive signal to the ion generator sub-assembly. When the ion generator sub-assembly receives the drive signal and starts to operate, it outputs an operation condition signal to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B9 Open in Ion Generator Circuit Open in ion generator sub-assembly circuit
·

Harness or connector between ion generator sub-assembly and IG circuit

·

Harness or connector between ion generator sub-assembly and body ground

·

Harness or connector between ion generator sub-assembly and air conditioning amplifier assembly

·

Ion generator sub-assembly

·

Air conditioning amplifier assembly


Memorized
(12 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E334627E03
0.115,0.281 1.063,0.688 0.948,0.406 10 false from IG1-NO. 1 Relay 1.656,0.417 3.49,0.615 1.833,0.198 10 false ECU-IG1 NO.4 2.583,0.188 2.74,0.385 0.156,0.198 10 false 1 2.771,0.313 3.083,0.51 0.313,0.198 10 false IG+ 2.583,1.521 2.74,1.719 0.156,0.198 10 false 4 2.771,1.625 3.229,1.823 0.458,0.198 10 false GND 4.438,0.417 4.594,0.615 0.156,0.198 10 false 3 4.146,0.417 4.604,0.615 0.458,0.198 10 false IG+ 4.094,1.427 4.552,1.625 0.458,0.198 10 false PCL 4.438,1.417 4.594,1.615 0.156,0.198 10 false 2 5.323,1.417 5.938,1.615 0.615,0.198 10 false NANO 5.125,1.417 5.281,1.615 0.156,0.198 10 false 7 5.052,0.427 5.365,0.625 0.313,0.198 10 false 26 5.313,0.427 5.927,0.625 0.615,0.198 10 false NAIN 6.083,1.521 6.396,1.719 0.313,0.198 10 false IC 2.677,2.26 2.99,2.458 0.313,0.198 10 false G2 6.073,0.135 6.385,0.333 0.313,0.198 10 false 5 V 2.677,2.417 4.719,2.792 2.042,0.375 10 false Ion Generator Sub-assembly 4.958,2.219 5.271,2.417 0.313,0.198 10 false F73 4.958,2.385 7.156,2.792 2.198,0.406 10 false Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the auxiliary battery voltage is low, the ion generator may not operate. When "Operation of Electrical Items Restricted." is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.

Click herePower Source / Network>2ZR-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

·

If the auxiliary battery voltage is low, the ion generator may not operate. When "Operation of Electrical Items Restricted." is not displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Ion Generator Ion generator sub-assembly OFF, ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Ion Generator
50004 121 94
OK:

Ion generator sub-assembly operates normally.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - POWER SOURCE)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

6.CHECK FOR DTC
2.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - POWER SOURCE)
a.

Disconnect the G2 ion generator sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-1 (IG+) -Body ground Power switch on (IG) 11 to 14 V
G2-1 (IG+) -Body ground Power switch on (IG) Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F73 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-26 (NAIN) - G2-3 (IG+) Always Below 1 Ω
F73-7 (NANO) - G2-2 (PCL) Always Below 1 Ω
F73-26 (NAIN) or G2-3 (IG+) - Body ground Always 10 kΩ or higher
F73-7 (NANO) or G2-2 (PCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY COMMUNICATION POWER SUPPLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY COMMUNICATION POWER SUPPLY
a.

Reconnect the F73 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G2-3 (IG+) - Body ground
·

Power switch on (IG)

·

Blower switch off


4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.CHECK ION GENERATOR SUB-ASSEMBLY OUTPUT

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.CHECK ION GENERATOR SUB-ASSEMBLY OUTPUT
a.

Reconnect the G2 air conditioning amplifier assembly connector.


b.
E328993C24
1.135,0.188 1.604,0.49 0.469,0.302 2.208,1.927 1.635,1.344 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.219,0.25 1.531,0.448 0.313,0.198 10 false F73 2.281,1.896 3.042,2.177 0.76,0.281 10 false NAIN
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F73-26 (NAIN) - Body ground
·

Power switch on (IG)

·

Blower switch Lo


Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE ION GENERATOR SUB-ASSEMBLY

6.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY