Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRILLE SHUTTER SYSTEM › 2016.10–2019.09
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0301245 GRILLE SHUTTER SYSTEM J

EXTERIOR PANELS / TRIM  GRILLE SHUTTER SYSTEM  Grille Shutter does not Operate  


DESCRIPTION

The swing grille actuator assembly receives signals from the ECM, hybrid vehicle control ECU and air conditioning amplifier assembly via CAN communication. Based on these signals, the swing grille actuator assembly operates the radiator shutter sub-assembly.

WIRING DIAGRAM

C360604E03
0.771,1.281 2.177,1.521 1.406,0.24 10 false from Auxiliary Battery 2.865,1.479 3.802,1.698 0.938,0.219 10 false ECU-B NO. 2 5.5,1.208 5.635,1.406 0.135,0.198 10 false 1 5.479,2.302 5.615,2.5 0.135,0.198 10 false 3 5.729,2.396 6.094,2.604 0.365,0.208 10 false GND 5.719,1.198 6.083,1.406 0.365,0.208 10 false +B 5.531,2.927 5.896,3.135 0.365,0.208 10 false A32 5.521,3.073 6.844,3.604 1.323,0.531 10 false Swing Grille Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, change the grille shutter control mode to maintenance mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION

·

If the swing grille actuator assembly has been replaced with a new one, perform initialization and change the grille shutter control mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK FOR FOREIGN OBJECT
a.

Check that the radiator shutter sub-assembly is free of foreign matter and ice.

OK:

The radiator shutter sub-assembly is free of foreign matter and ice.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - POWER SUPPLY AND BODY GROUND)

NG

FOREIGN OBJECT (REMOVE FOREIGN MATTER AND/OR ICE)

2.CHECK HARNESS AND CONNECTOR (SWING GRILLE ACTUATOR ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
B438373C05
0.438,1.26 0.781,1.521 0.344,0.26 1.135,1.917 1.292,1.469 true 1.833,1.917 1.646,1.479 true 0.156,0.135 0.469,0.292 0.313,0.156 10 false *a 0.5,1.313 0.813,1.469 0.313,0.156 10 false A32 0.979,1.938 1.292,2.094 0.313,0.156 10 false +B 1.813,1.938 2.344,2.177 0.531,0.24 10 false GND
*a Front view of wire harness connector
(to Swing Grille Actuator Assembly)


Disconnect the swing grille actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A32-1 (+B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grille Shutter / Active Test.


e.

According to the display on the GTS, perform the Active Test to open and close the grille shutter.

Body Electrical > Grille Shutter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Shutter Closing Operation Lock Detection Function to perform a closing operation until motor lock is detected and the motor stops OFF/Close -
Shutter Opening Operation Lock Detection Function to perform an opening operation until motor lock is detected and the motor stops OFF/Open -
Body Electrical > Grille Shutter > Active Test
Tester Display
Shutter Closing Operation Lock Detection
50004 352 3
Body Electrical > Grille Shutter > Active Test
Tester Display
Shutter Opening Operation Lock Detection
50004 352 4

f.

Enter the following menus: Body Electrical / Grille Shutter / Data List.


g.

Read the Data List according to the display on the GTS.

Body Electrical > Grille Shutter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shutter Operation Lock Detection Result for Active Test Result of Active Test Shutter Closing Operation Lock Detection and Shutter Opening Operation Lock Detection Normal, Open Error or Close Error Normal: Normal lock detected
Open Error: Lock detected in abnormal position while performing Active Test Shutter Opening Operation Lock Detection
Close Error: Lock detected in abnormal position while performing Active Test Shutter Closing Operation Lock Detection
Body Electrical > Grille Shutter > Data List
Tester Display
Shutter Operation Lock Detection Result for Active Test
50003 352 8
OK:

"Normal" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK RADIATOR SHUTTER SUB-ASSEMBLY
4.CHECK RADIATOR SHUTTER SUB-ASSEMBLY
a.

Remove the radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

Remove the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


c.

Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.

OK:

The radiator shutter sub-assembly moves smoothly.



Result:
Proceed to
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPLACE RADIATOR SHUTTER SUB-ASSEMBLY