Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061825 SEAT _0301288 FRONT SEAT ASSEMBLY A

SEAT  FRONT SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 72443B 1.INSTALL VERTICAL ADJUSTER GEAR LH (w/ Vertical Adjuster)

a.

Install the front seat vertical adjuster assembly.

i.
B456120

Install the front vertical adjuster brake sub-assembly LH.

NOTICE:

Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.



ii.
B456118

Install the vertical adjuster spacer.


iii.
B456117N01
2.615,0.667 2.771,0.865 0.156,0.198 10 true 1 0.979,0.74 1.135,0.938 0.156,0.198 10 true 2 2.688,1.323 2.844,1.521 0.156,0.198 10 true 3

Install the vertical adjuster plate with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.




Hide 82824A 2.INSTALL CONNECTOR MALE HOUSING (w/o Seat Heater System)

a.
B458521

Engage the claw to install the connector male housing.


Hide 82667D 3.INSTALL CONNECTOR HOLDER (for Front Passenger Side)

a.
B458525

Engage the claw to install the connector holder.


Hide 72211C 4.INSTALL SEAT TRACK ADJUSTING HANDLE

a.
B453968

Engage the claws to install the seat track adjusting handle to the front seat adjuster assembly.


Hide 71052A 5.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY

a.
B453967

Engage the hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.


Hide 7181B 6.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER

a.
B453966

Engage the claw to install the front seat cushion wire harness holder.


b.

Install the 2 screws.


Hide 82192 7.INSTALL FRONT SEAT WIRE (for Driver Side)

a.
B453965

Engage the claw.


b.

Disengage the clamps to install the front seat wire.


Hide 82191 8.INSTALL FRONT SEAT WIRE (for Front Passenger Side)

a.
B458520

Engage the claw.


b.

Disengage the clamps to install the front seat wire.


Hide 8219B 9.INSTALL NO. 2 FRONT SEAT WIRE

a.
B458493

Engage the claw and clamp to install the No. 2 front seat wire.


Hide 71875G 10.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Driver Side)

a.
B453962

Engage the claws to install the LH seat reclining adjuster inside cover RH.


Hide 71876G 11.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Driver Side)

a.
B453961

Engage the claws to install the LH seat reclining adjuster inside cover LH.


b.
B453960

w/ Lumbar Support:

i.

Engage the claw.



Hide 71875F 12.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Front Passenger Side)

a.
B453964

Engage the claws to install the RH seat reclining adjuster inside cover RH.


Hide 71876F 13.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)

a.
B453963

Engage the claws to install the RH seat reclining adjuster inside cover LH.


Hide 71873A 14.INSTALL FRONT SEAT LOWER CUSHION SHIELD (w/ Vertical Adjuster)

a.
B453959C02
2.344,0.5 3.094,0.5 true 1.99,1.542 2.74,1.542 true 3.146,0.396 3.344,0.646 0.198,0.25 10 false *a 2.792,1.417 2.99,1.667 0.198,0.25 10 false *b
*a Hook
*b Guide


Engage the claw and guide.


b.

Engage the hook to install the front seat lower cushion shield.


Hide 71874A 15.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)

a.
B453958C03
2.333,0.698 3.063,0.698 true 1.906,1.49 2.635,1.49 true 3.115,0.573 3.365,0.823 0.25,0.25 10 false *a 2.698,1.385 3.01,1.583 0.313,0.198 10 false *b
*a Hook
*b Guide


Engage the claw and guide.


b.

Engage the hook to install the front seat lower cushion shield LH.


Hide 87510L 16.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71072S 17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

NOTICE:

When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION


a.
B458475

Engage the claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.

NOTICE:

Be careful not to damage the separate type front seat cushion cover.



Hide 18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Engage the hooks (A) and hooks (B) to install the separate type front seat cushion cover with pad.

B453956E01
3.104,0.594 3.521,0.177 true 3.948,0.594 3.531,0.177 true 0.802,1.198 1.271,0.896 true 0.813,1.208 1.25,1.625 true 0.802,1.24 1.26,2.323 true 3.229,2.25 3.5,2.573 true 3.823,2.26 3.51,2.573 true 5.74,0.948 6.375,1.271 true 5.74,1.594 6.375,1.281 true 5.75,1.948 6.396,1.281 true 3.448,0.031 3.74,0.219 0.292,0.188 10 false (A) 0.531,1.115 0.781,1.271 0.25,0.156 10 true (B) 3.417,2.583 3.698,2.75 0.281,0.167 10 false (B) 6.417,1.219 6.708,1.406 0.292,0.188 10 true (B)


b.
B453955

Engage the hooks.


c.

for Front Passenger Side:

i.
B475983

Engage the claw to install the occupant detection sensor connector.



d.

w/ Seat Heater System:

i.

Connect the connector.


ii.
B453954

Engage the clamp.



Hide 82192B 19.INSTALL NO. 2 FRONT SEAT WIRE (w/ Lumbar Support)

a.
B453953

Engage the clamp to install the No. 2 front seat wire.


Hide 71759B 20.INSTALL FRONT SEATBACK HOOK

a.
B453952

Engage the claws to install the 2 front seatback hooks from the front seatback frame sub-assembly.


Hide 71054S 21.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)

a.
B458494

Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.


b.
B458477C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.


c.
B453950

Engage the claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.


Hide 72760D 22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

Hide 73920A 23.INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

Hide 87510N 24.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71074S 25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

NOTICE:

When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION


a.

w/ Front Seat Airbag Assembly:

i.
B458476

Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.

NOTICE:

Be careful not to damage the separate type front seatback cover.




b.

w/o Front Seat Airbag Assembly:

i.
B460364

Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.

NOTICE:

Be careful not to damage the separate type front seatback cover.




Hide 26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.

Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.


Hide 71931 27.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B458474C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the 2 front seat headrest supports as shown in the illustration.


b.
B458473

Close the 2 fasteners as shown in the illustration.


c.

w/ Seat Heater System:

i.
B453946

Engage the clamp.



d.
B453945

Engage the hooks.


Hide 28.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B453944

Engage the guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.


b.

Install the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B453943

w/ Front Seat Side Airbag

i.

Engage the claw and clamps to install the front seat airbag assembly wire harness.

HINT:

Engage the claw first.




d.

w/ Seat Heater System:

i.
B453942

Engage the clamp.


ii.

Connect the connector.



e.

w/ Lumbar Support:

i.
B453941

Engage the clamp.


ii.

Connect the connector.



f.
B453940

Engage the hooks.


Hide 72497B 29.INSTALL VERTICAL ADJUSTER BRACKET COVER (w/ Vertical Adjuster)

a.
B453939

Engage the claw to install the vertical adjuster bracket cover.


Hide 71862 30.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)

a.
B458470C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and guides as shown in the illustration.


b.
B458497C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front seat inner cushion shield as shown in the illustration.


Hide 84922A 31.INSTALL FRONT LUMBAR POWER SEAT SWITCH (w/ Lumbar Support)

Hide 71812D 32.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)

a.
B453932

w/ Lumbar Support:

i.

Connect the connector.


ii.

Engage the clamps.



b.
B458469C01
0.271,1.333 0.854,1.333 true 1.333,0.167 2.5,0.167 true 1.802,0.167 1.802,0.583 1.802,0.583 2.219,0.583 true 0.021,1.25 0.25,1.458 0.229,0.208 10 true (A) 1,0.083 1.24,0.271 0.24,0.188 10 true (B)
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide (A) as shown in the illustration.


c.

Engage the claws and guides (B) as shown in the illustration.


d.
B458496C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front seat cushion shield as shown in the illustration.


Hide 71849F 33.INSTALL SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)

a.
B458468C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides as shown in the illustration.


b.

Engage the claws to install the seat adjuster cover cap as shown in the illustration.


Hide 71861 34.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)

a.
B458472C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and guides as shown in the illustration.


b.
B458499C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front seat inner cushion shield as shown in the illustration.


Hide 71811D 35.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)

a.
B458471C01
2.76,1.167 3.094,1.167 true 0.74,0.167 1.917,0.167 true 0.885,0.333 1.417,0.333 1.417,0.333 1.417,0.167 true 1.99,0.083 2.229,0.292 0.24,0.208 10 true (B) 3.167,1.073 3.385,1.271 0.219,0.198 10 true (A)
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide (A) as shown in the illustration.


b.

Engage the claws and guides (B) as shown in the illustration.


c.
B458498C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front seat cushion shield as shown in the illustration.


Hide 72526A 36.INSTALL RECLINING ADJUSTER RELEASE HANDLE

a.
B453928

Engage the guide to install the reclining adjuster release handle.


Hide 72538 37.INSTALL RECLINING HINGE OUTER COVER

a.
B458467C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw to install the reclining hinge outer cover as shown in the illustration.


Hide 72495 38.INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)

a.
B458466C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the vertical adjusting handle as shown in the illustration.


Hide 71074S 39.CONNECT SEPARATE TYPE FRONT SEATBACK COVER

a.
B453925

Connect the rubber band of the separate type front seatback cover.


Hide 73240 40.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

Hide 73230 41.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

Hide 87501B 42.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

Hide 89178A 43.INSTALL SEAT POSITION AIRBAG SENSOR

Hide 72277A 44.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR