Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM32K0E _57 Power Source / Network _059857 NETWORKING _0298527 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN Any of the following conditions is met:
·

Errors in LIN communication between ECUs.

·

Open in communication lines.

·

Short in communication lines.

·

The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more.


·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

ID code box (immobiliser code ECU)

·

Wire harness or connector

·

AM2 fuse

·

STRG LOCK fuse

·

ECU-B NO. 1 fuse



DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - ○ ○ ○ ○
Malfunction Status Errors in LIN communication between ECUs ○ - - -
Open in communication lines - ○ - -
Short in communication lines - - ○ -
The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines - - - ○
Detection Time - - - 7 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

B415960E13
4.208,0.198 5.896,0.417 1.688,0.219 10 false from Auxiliary Battery 1.552,1.979 2.625,2.177 1.073,0.198 10 false F1 1.552,2.135 3.083,2.531 1.531,0.396 10 false Certification ECU (Smart Key ECU Assembly) 5.875,1.344 6.948,1.542 1.073,0.198 10 false STRG LOCK 3.698,1.99 4.771,2.188 1.073,0.198 10 false F78 3.698,2.167 6.396,2.573 2.698,0.406 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 1.552,4.104 2.625,4.302 1.073,0.198 10 false F21 1.552,4.271 3.125,4.625 1.573,0.354 10 false ID Code Box (Immobiliser Code ECU) 0.979,5.333 2.75,5.604 1.771,0.271 10 false : LIN Communication Line 0.5,3.396 1.573,3.594 1.073,0.198 10 false ECU-B NO. 1 0.615,1.323 1.104,1.521 0.49,0.198 10 false AM2 2.667,1.438 3.156,1.635 0.49,0.198 10 false LIN 2.615,3.552 3.104,3.75 0.49,0.198 10 false LIN1 4.115,1.438 4.604,1.635 0.49,0.198 10 false LIN 1.698,1.177 2.188,1.375 0.49,0.198 10 false +B 1.719,3.26 2.208,3.458 0.49,0.198 10 false +B 5.167,1.177 5.656,1.375 0.49,0.198 10 false B 1.719,1.646 2.208,1.844 0.49,0.198 10 false E 1.719,3.708 2.208,3.906 0.49,0.198 10 false GND 4.958,1.646 5.448,1.844 0.49,0.198 10 false GND 2.979,1.26 3.469,1.458 0.49,0.198 10 false 13 3.927,1.26 4.417,1.458 0.49,0.198 10 false 5 5.354,1.104 5.844,1.302 0.49,0.198 10 false 7 5.365,1.563 5.854,1.76 0.49,0.198 10 false 1 1.521,1.073 2.01,1.271 0.49,0.198 10 false 4 1.469,1.542 1.958,1.74 0.49,0.198 10 false 18 1.531,3.146 2.021,3.344 0.49,0.198 10 false 1 1.531,3.604 2.021,3.802 0.49,0.198 10 false 5 2.979,3.365 3.469,3.563 0.49,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, refer to Service Bulletin.

·

Before performing the inspection, check that DTC B2786, B2789 or B278C is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
F1-13 (LIN) - F21-2 (LIN1) Power switch off Below 1 Ω
F1-13 (LIN) - F78-5 (LIN) Power switch off Below 1 Ω
F1-13 (LIN), F78-5 (LIN) or F21-2 (LIN1) - Body ground Power switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY))
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the F21 ID code box (immobiliser code ECU) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

3.CHECK FOR DTC (ID CODE BOX (IMMOBILISER CODE ECU))

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

3.CHECK FOR DTC (ID CODE BOX (IMMOBILISER CODE ECU))
a.

Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)