Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0301367 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the power switch is on (ACC), 1 or more times, the radio and display receiver assembly does not receive the signal for 30 seconds or more
·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E268494E96
1.656,0.438 2.271,0.635 0.615,0.198 10 false MSCH 1.667,1.083 2.281,1.281 0.615,0.198 10 false MSCL 5.083,0.427 5.698,0.625 0.615,0.198 10 false CNH1 5.094,1.083 5.708,1.281 0.615,0.198 10 false CNL1 2.156,0.281 2.771,0.479 0.615,0.198 10 false 36 2.156,0.927 2.771,1.125 0.615,0.198 10 false 37 4.906,0.292 5.521,0.49 0.615,0.198 10 false 3 4.906,0.927 5.521,1.125 0.615,0.198 10 false 4 0.781,1.552 1.396,1.75 0.615,0.198 10 false F4 0.771,1.719 2.74,1.948 1.969,0.229 10 false Combination Meter Assembly 4.771,1.542 5.385,1.74 0.615,0.198 10 false F50 4.771,1.698 6.49,2.083 1.719,0.385 10 false Radio and Display Receiver Assembly 0.906,2.24 3.271,2.469 2.365,0.229 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK DTC (METER / GAUGE SYSTEM)
a.

Check for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F50 radio and display receiver assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-3 (CNH1) - F4-36 (MSCH) Always Below 1 Ω
F50-4 (CNL1) - F4-37 (MSCL) Always Below 1 Ω
F50-3 (CNH1) - Body ground Always 10 kΩ or higher
F50-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG