Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
68131
1.CLEAN BACK DOOR GLASS
When reusing the back door glass:
Using a scraper, remove any remaining adhesive residue from the back window glass.
Be careful not to damage the back window glass.
Clean the outer circumference of the back window glass with a non-residue solvent.
Do not touch the back window glass surface after cleaning it.
Even if using a new back window glass, clean it with a nonresidue solvent.
2.INSTALL BACK DOOR GLASS SPACER (for Upper Side)
Using a brush or sponge, coat the installation area of the new back door glass spacer with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the 2 new back door glass spacers to the back door glass as shown in the illustration.
3.INSTALL BACK DOOR GLASS SPACER (for Side)
Using a brush or sponge, coat the installation area of the new back door glass spacer with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the 4 new back door glass spacers to the back door glass as shown in the illustration.
75575D
4.INSTALL BACK WINDOW LOWER MOULDING
Using a brush or sponge, coat the installation area of a new back window lower moulding with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Back Door Glass |
Install the new back window lower moulding to the back door glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 10.3 mm (0.406 in.) |
| b | 18.5 mm (0.728 in.) |
| c | 15.1 mm (0.594 in.) |
5.INSTALL NO. 2 BACK WINDOW GLASS SPACER
Using a brush or sponge, coat the installation area of a new No. 2 back window glass spacer with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the new No. 2 back window glass spacer to the back door glass as shown in the illustration.
6.INSTALL NO. 1 BACK WINDOW GLASS SPACER
Use the same procedure as for the No. 2 back window glass spacer.
7.INSTALL BACK WINDOW OUTSIDE MOULDING LH
Using a brush or sponge, coat the installation area of a new back window outside moulding LH with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *a | Back Side of Back Door Glass |
Install the new back window outside moulding LH to the back door glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 9.9 mm (0.390 in.) |
8.INSTALL BACK WINDOW OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
68131
9.INSTALL BACK DOOR GLASS
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Back door glass preliminary installation procedures:
Install the suction cups to the back door glass.
Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and upper portion and sides of the back door glass is even.
| *a | Matchmark |
Position the back door glass.
Using suction cups, place the back door glass in the correct position.
Check that the whole contact surface of the back door glass rim is perfectly even.
Align the matchmarks on the back door glass and back door panel.
Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.
Remove the back door glass.
Using a brush, coat the installation surfaces on the back door panel with primer M.
Do not coat the adhesive with primer M.
Do not apply too much primer M.
Allow the primer M to dry for 3 minutes or more.
Throw away any leftover primer M.
If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.
Using a brush or sponge, coat the adhesive application area with primer G.
| *a | Back Side of Back Door Glass | *b | Adhesive Positioning Center |
| *c | Ceramic Notch | - | - |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 7.0 mm (0.276 in.) or more |
| b | 15.3 mm (0.602 in.) |
| c | 7.0 mm (0.276 in.) or more |
| d | 18.5 mm (0.728 in.) |
| e | 7.0 mm (0.276 in.) or more |
| f | 12.3 mm (0.484 in.) |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Apply primer G to the ceramic notches.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Apply adhesive to the back door glass.
Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent
| *a | Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 to 15.0 mm (0.472 to 0.591 in.) |
| b | 8.0 to 11.0 mm (0.315 to 0.433 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass as shown in the illustration.
| *a | Back Side of Back Door Glass | *b | Adhesive Positioning Center |
| *c | Ceramic Notch | - | - |
|
Adhesive | - | - |
| Area | Dimension |
|---|---|
| a | 15.3 mm (0.602 in.) |
| b | 18.5 mm (0.728 in.) |
| c | 12.3 mm (0.484 in.) |
Apply adhesive to the ceramic notches.
Install the back door glass.
| *a | Matchmark |
Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.
Check that the No. 1 and No. 2 back window glass spacers are engaged to the back door panel correctly.
Check the clearance between the back door panel and back door glass.
Lightly press the outer surface of the back door glass to ensure a close fit and engage the No. 1 back window glass spacer and No. 2 back window glass spacer.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the back door glass using protective tape until the applied adhesive becomes hard.
Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.
Connect each connector and engage each clamp.
82184
10.CONNECT NO. 1 BACK DOOR WIRE
Connect the 2 connectors to the back door glass.
w/ Glass Breakage Sensor:
Connect the connector to the glass breakage sensor.
86300C
11.CONNECT NO. 2 AMPLIFIER ANTENNA ASSEMBLY (w/ Woofer)
Disconnect the connector.
85110R
12.INSTALL REAR LIGHT ASSEMBLY (for Bulb Type)
85110R
13.INSTALL REAR LIGHT ASSEMBLY (for LED Type)
85110R
14.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
15.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
76871
16.INSTALL REAR SPOILER