Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM32K0E _59 Vehicle Exterior _061789 WIPER / WASHER _0304154 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110R 1.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the connector.


Hide 85143R 2.INSTALL REAR WIPER MOTOR GROMMET

a.
E356885C02
1.479,0.375 1.729,0.594 1.729,0.594 1.979,0.375 true 1.656,0.604 1.844,0.802 0.188,0.198 10 false *a
*a Rear Wiper Motor Grommet Lip


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.
E356886C02
1.76,0.656 2.052,0.448 true 2.115,0.354 2.427,0.51 0.313,0.156 10 false *a
*a Alignment Mark


Install the rear wiper motor grommet.

HINT:

Install the rear wiper motor grommet with its alignment mark facing up.



Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
E356887C02
1.333,0.927 1.583,1.313 true 2.021,3.469 2.333,3.656 true 1.125,0.823 1.313,1 0.188,0.177 10 false *a 2.396,3.573 2.583,3.75 0.188,0.177 10 false *a
*a Serration


When reusing the rear wiper arm and blade assembly:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the rear wiper motor assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Turn the power switch on (IG).


d.

Operate the rear wiper motor assembly and stop it at the automatic stop position.


e.

Turn the power switch off.


f.
E356879C04
2.104,0.552 2.479,0.802 true 1.865,0.438 2.052,0.635 0.188,0.198 10 true *a 2.656,0.49 2.813,0.688 0.156,0.198 10 true A 2.719,0.802 2.875,1 0.156,0.198 10 true A
*a Alignment Mark


Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the rear wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10.0 mm (0.394 in.)



g.

Turn the power switch on (IG).


h.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not contact the vehicle body.


i.

Turn the power switch off.


j.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


k.
E356888C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Engage the claws and guides to close the rear wiper arm head cap as shown in the illustration.


l.
E356889

Slide the rear wiper arm head cap to engage the claws as shown in the illustration.


Hide 64780A 4.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

Hide 67938A 5.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 6.INSTALL BACK DOOR SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64790B 7.INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY