Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0302427 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E360100E01
4.906,2.188 6.875,2.76 1.969,0.573 10 false Radio and Display Receiver Assembly 4.927,2.01 5.542,2.208 0.615,0.198 10 false F125 5.083,1.542 5.698,1.74 0.615,0.198 10 false MIN- 5.073,0.708 5.688,0.906 0.615,0.198 10 false SNS2 4.813,1.385 5.125,1.583 0.313,0.198 10 false 19 4.854,0.594 5.167,0.792 0.313,0.198 10 false 6 2.146,0.583 2.458,0.781 0.313,0.198 10 false 1 2.167,1.375 2.479,1.573 0.313,0.198 10 false 7 1.646,1.479 2.365,1.719 0.719,0.24 10 false MCO- 1.677,0.698 2.396,0.938 0.719,0.24 10 false SNS2 0.865,2.156 2.865,2.76 2,0.604 10 false Map Light Assembly (Telephone Microphone Assembly) 0.875,2 1.49,2.198 0.615,0.198 10 false R2

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E360105C01
1.458,0.521 1.875,0.813 0.417,0.292 2.073,1.99 2.365,2.615 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.583 1.917,0.823 0.406,0.24 10 false F125 2.365,2.635 2.771,2.875 0.406,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F125-19 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F125-6 (SNS2) - Body ground Always 10 kΩ or higher
F125-19 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).


b.
E265420C11
1.042,1.615 1.365,1.125 true 2.594,1.646 2.208,1.146 true 0.188,0.208 0.5,0.406 0.313,0.198 10 false *a 2.51,1.688 2.979,1.896 0.469,0.208 10 false SNS2 0.771,1.656 1.24,1.865 0.469,0.208 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)