Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0302427 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E361252E01
5.875,3.073 7.063,3.5 1.188,0.427 10 false Radio and Display Receiver Assembly 0.458,3.052 2.427,3.438 1.969,0.385 10 false Map Light Assembly (Telephone Microphone Assembly) 0.458,2.885 0.771,3.083 0.313,0.198 10 false R2 5.885,2.917 6.604,3.094 0.719,0.177 10 false F125 5.927,2.448 6.656,2.646 0.729,0.198 10 false SNS2 5.927,1.885 6.656,2.083 0.729,0.198 10 false SGND 5.938,1.5 6.667,1.698 0.729,0.198 10 false MIN- 5.927,1.031 6.656,1.229 0.729,0.198 10 false MIN+ 5.927,0.552 6.656,0.75 0.729,0.198 10 false MACC 0.844,2.469 1.573,2.667 0.729,0.198 10 false SNS2 0.844,1.49 1.573,1.688 0.729,0.198 10 false MCO- 0.823,1 1.552,1.198 0.729,0.198 10 false MCO+ 0.823,0.542 1.552,0.74 0.729,0.198 10 false MACC 1.333,0.427 1.49,0.625 0.156,0.198 10 false 9 1.333,1.375 1.49,1.573 0.156,0.198 10 false 7 1.333,0.917 1.49,1.115 0.156,0.198 10 false 8 1.333,2.302 1.49,2.5 0.156,0.198 10 false 1 5.74,2.333 5.896,2.531 0.156,0.198 10 false 6 5.677,1.75 6.938,1.948 1.26,0.198 10 false 18 5.677,1.365 6.896,1.573 1.219,0.208 10 false 19 5.719,0.927 5.875,1.125 0.156,0.198 10 false 5 5.729,0.406 5.885,0.604 0.156,0.198 10 false 4 3.302,2.021 4.031,2.219 0.729,0.198 10 false (Shielded)

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F125 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-6 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F125-4 (MACC) - R2-9 (MACC) Always Below 1 Ω
F125-5 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F125-19 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F125-6 (SNS2) or R2-1 (SNS2) - Body ground Always 10 kΩ or higher
F125-4 (MACC) or R2-9 (MACC) - Body ground Always 10 kΩ or higher
F125-5 (MIN+) or R2-8 (MOC+) - Body ground Always 10 kΩ or higher
F125-19 (MIN-) or R2-7 (MCO-) - Body ground Always 10 kΩ or higher
F125-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.
E359760C02
1.427,0.625 1.896,0.917 0.469,0.292 1.115,2.635 2.052,1.99 true 2.24,1.75 2.917,1.344 true 2.219,2 2.635,2.563 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.542,0.688 2.302,0.885 0.76,0.198 10 false F125 2.938,1.167 3.427,1.479 0.49,0.313 10 false MACC 2.594,2.625 3.052,2.875 0.458,0.25 10 false SGND 0.865,2.625 1.25,2.844 0.385,0.219 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F125-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-18 (SGND) - Body ground Always Below 1 Ω
F125-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E358190C06
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 3.219,1.958 0.635,0.188 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F125 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)