The navigation ECU and the radio and display receiver assembly are connected via LVDS communication line.
This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1532 | LVDS Signal Malfunction (from Extension Module) | When any of the following conditions is met:
·
Video signal (digital) is lost. ·
Navigation ECU is/was not connected while the power switch is/was on (ACC) or on (IG). ·
Communication between the master unit and the navigation ECU is/was not possible when the hybrid control system is/was started. |
·
Navigation ECU power source circuit ·
LVDS circuit between radio and display receiver assembly and navigation ECU ·
Navigation ECU ·
Radio and display receiver assembly ·
Harness and connector |
Even if no malfunction is present, this DTC may be stored depending on the auxiliary battery condition or hybrid control system start voltage.
The radio and display receiver assembly is the master unit.
Disconnect the F83 navigation ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F83-2 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Navigation ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F83-1 (+B) - F83-2 (GND) | Power switch off | 11 to 14 V |
| F83-3 (ACC) - F83-2 (GND) | Power switch on (ACC) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the harness and connector (LVDS communication line) with a new or known good one.
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation ECU with a new or known good one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Disconnect the F80 radio and display receiver assembly connector.
Disconnect the F83 navigation ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F80-4 (+B2) - F83-1 (+B) | Always | Below 1 Ω |
| F80-3 (ACC2) - F83-3 (ACC) | Always | Below 1 Ω |
| F80-8 (GND2) - F83-2 (GND) | Always | Below 1 Ω |
| F80-4 (+B2) - Body ground | Always | 10 kΩ or higher |
| F80-3 (ACC2) - Body ground | Always | 10 kΩ or higher |
| F80-8 (GND2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG