Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0302427 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C0  GPS Antenna Disconnected (Short)  B15C1  GPS Antenna Disconnected (Open)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Disconnected (Short) Navigation antenna error
·

Navigation ECU

·

Roof Antenna Assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly


B15C1 GPS Antenna Disconnected (Open) Error of the power source to the navigation antenna
·

Navigation ECU

·

Roof Antenna Assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly



WIRING DIAGRAM

E359865E04
0.052,2.281 1.698,2.49 1.646,0.208 10 false Roof Antenna Assembly 5.844,2.365 7.031,2.74 1.188,0.375 10 false Navigation ECU 5.833,1.417 6.292,1.615 0.458,0.198 10 false GPS 5.469,1.417 5.781,1.615 0.313,0.198 10 false GB 5.469,1.844 5.781,2.042 0.313,0.198 10 false GB 4.438,1.406 4.594,1.604 0.156,0.198 10 false A 4.438,1.844 4.594,2.042 0.156,0.198 10 false A 4.063,1.396 4.219,1.594 0.156,0.198 10 false B 4.063,1.854 4.219,2.052 0.156,0.198 10 false B 2.729,1.406 2.885,1.604 0.156,0.198 10 false C 2.729,1.854 2.885,2.052 0.156,0.198 10 false C 2.365,1.396 2.521,1.594 0.156,0.198 10 false D 2.365,1.854 2.521,2.052 0.156,0.198 10 false D 1.219,1.396 1.531,1.594 0.313,0.198 10 false RA 1.219,1.844 1.531,2.042 0.313,0.198 10 false RA 1.26,1.208 1.417,1.406 0.156,0.198 10 false 5 1.24,1.656 1.552,1.854 0.313,0.198 10 false 5a 2.365,1.208 2.521,1.406 0.156,0.198 10 false 2 2.729,1.208 2.885,1.406 0.156,0.198 10 false 2 4.052,1.208 4.208,1.406 0.156,0.198 10 false 2 4.458,1.208 4.615,1.406 0.156,0.198 10 false 2 5.531,1.219 5.688,1.417 0.156,0.198 10 false 1 2.333,1.656 2.646,1.854 0.313,0.198 10 false 2a 2.698,1.656 3.01,1.854 0.313,0.198 10 false 2a 4.021,1.656 4.333,1.854 0.313,0.198 10 false 2a 4.406,1.656 4.719,1.854 0.313,0.198 10 false 2a 5.479,1.656 5.792,1.854 0.313,0.198 10 false 1a 4.979,2.292 5.292,2.49 0.313,0.198 10 false *1 3.396,2.292 3.708,2.49 0.313,0.198 10 false *2 1.792,2.292 2.104,2.49 0.313,0.198 10 false *3 1.438,2.698 5.875,2.896 4.438,0.198 10 false *1: Antenna Cord Sub-assembly 1.438,3.042 5.875,3.24 4.438,0.198 10 false *2: No. 2 Antenna Cord Sub-assembly 1.438,3.365 5.875,3.563 4.438,0.198 10 false *3: No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 3 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>ANTENNA CORD>REMOVAL


b.
E359866C01
0.438,3.281 0.854,3.542 0.417,0.26 0.167,1.156 0.583,1.417 0.417,0.26 1.885,3.583 2.292,3.583 true 2.135,1.823 2.135,1.438 true 0.219,0.427 0.531,0.625 0.313,0.198 10 false *a 0.229,2.823 0.542,3.021 0.313,0.198 10 false *b 0.552,3.344 0.865,3.542 0.313,0.198 10 false RA 0.333,1.208 0.49,1.406 0.156,0.198 10 false D 2.333,3.51 2.646,3.708 0.313,0.198 10 false 5a 2.073,1.865 2.385,2.063 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telephone Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-2 - RA-5 Always Below 1 Ω
D-2a - RA-5a Always Below 1 Ω
D-2 or RA-5 - Body ground Always 10 kΩ or higher
D-2a or RA-5a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>ANTENNA CORD>REMOVAL


b.
E359938C01
0.115,1.146 0.531,1.406 0.417,0.26 0.104,3.292 0.521,3.552 0.417,0.26 1.271,1.948 1.271,1.406 true 1.281,4.104 1.281,3.563 true 0.219,0.5 0.531,0.698 0.313,0.198 10 false *a 0.24,2.823 0.552,3.021 0.313,0.198 10 false *b 0.281,1.188 0.438,1.385 0.156,0.198 10 false C 0.26,3.344 0.417,3.542 0.156,0.198 10 false B 1.208,1.958 1.521,2.156 0.313,0.198 10 false 2a 1.229,4.146 1.542,4.344 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - B-2 Always Below 1 Ω
C-2a - B-2a Always Below 1 Ω
C-2 or B-2 - Body ground Always 10 kΩ or higher
C-2a or B-2a - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

b.
E359939C03
0.292,3.26 0.708,3.521 0.417,0.26 0.177,1.188 0.594,1.448 0.417,0.26 2.146,1.833 2.146,1.438 true 2.448,3.51 1.896,3.51 true 1.646,3.583 1.323,4.094 true 0.25,0.521 0.563,0.719 0.313,0.198 10 false *a 0.271,2.698 0.583,2.896 0.313,0.198 10 false *b 0.302,1.229 0.458,1.427 0.156,0.198 10 false A 0.396,3.302 0.708,3.5 0.313,0.198 10 false GB 2.094,1.885 2.406,2.083 0.313,0.198 10 false 2a 2.521,3.427 2.833,3.625 0.313,0.198 10 false 1a 0.958,4.042 1.417,4.24 0.458,0.198 10 false GPS
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - GB-1 (GPS) Always Below 1 Ω
A-2a - GB-1a Always Below 1 Ω
A-2 or GB-1 (GPS) - Body ground Always 10 kΩ or higher
A-2a or GB-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ROOF ANTENNA ASSEMBLY

NG

5.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG