Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2016.10–2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0303369 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B242E  Open in IG Circuit  


DESCRIPTION

This DTC is stored when a malfunction occurs in the headlight ECU sub-assembly LH IG power source circuit. The headlight ECU sub-assembly LH stores DTC B242E.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B242E Open in IG Circuit Open in the headlight ECU sub-assembly LH IG power source circuit
·

Headlight ECU sub-assembly LH

·

Harness or connector


-

WIRING DIAGRAM

E342807E04
4.229,1.865 6.708,2.125 2.479,0.26 10 false Headlight ECU Sub-assembly LH 4.24,1.698 4.604,1.906 0.365,0.208 10 false A16 4.708,1.021 5.073,1.229 0.365,0.208 10 false IG 5.51,1.021 5.875,1.229 0.365,0.208 10 false GND 5.885,0.927 6.25,1.135 0.365,0.208 10 false 12 4.542,0.927 4.906,1.135 0.365,0.208 10 false 4 3.813,0.927 4.177,1.135 0.365,0.208 10 false 10 1.031,0.958 2.01,1.469 0.979,0.51 10 true from IG1-NO. 1 Relay 2.573,1.198 3.594,1.448 1.021,0.25 10 false ECU-IG1 NO. 3 0.969,1.885 3.875,2.188 2.906,0.302 10 false Instrument Panel Junction Block Assembly 0.958,1.729 1.323,1.938 0.365,0.208 10 false 3F

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch to on (IG).


b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B242E is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - POWER SOURCE AND BODY GROUND)
a.

Disconnect the A16 headlight ECU sub-assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A16-4 (IG) - Body ground Power switch off Below 1 V
A16-4 (IG) - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR