Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0303371 TOYOTA PARKING ASSIST-SENSOR SYSTEM C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored when the clearance warning ECU assembly receives a steering angle sensor power supply malfunction signal via CAN communication from the spiral cable with sensor sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Either condition is met (1 trip detection logic*1):
·

Open in steering angle sensor power source

·

Short in steering angle sensor power source


·

Wire harness or connector

·

Spiral cable with sensor sub-assembly



*: Only output while a malfunction is present.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ ○
Malfunction Status Open in steering angle sensor power source ○ -
Short in steering angle sensor power source - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E362076E01
5.25,2.198 6.771,2.979 1.521,0.781 10 false Clearance Warning ECU Assembly 3.406,2.365 4.948,3.146 1.542,0.781 10 false Spiral Cable with Sensor Sub-assembly 3.438,2.188 4.042,2.417 0.604,0.229 10 false F69 3.646,1.76 4.25,1.99 0.604,0.229 10 false ESS 3.656,1.229 4.26,1.458 0.604,0.229 10 false IG1 3.656,0.656 4.26,0.885 0.604,0.229 10 false BAT 3.458,1.635 4.063,1.865 0.604,0.229 10 false 1 3.458,1.094 4.063,1.323 0.604,0.229 10 false 4 3.458,0.531 4.063,0.76 0.604,0.229 10 false 5 1.865,0.833 3.073,1.094 1.208,0.26 10 false ECU-DCC NO. 1 1.865,1.365 3.073,1.625 1.208,0.26 10 false ECU-IG1 NO. 2 0.229,1.208 1.729,1.51 1.5,0.302 10 false from IG1-NO. 1 Relay 0.26,0.604 1.729,0.938 1.469,0.333 10 false from Auxiliary Battery 1.198,3.24 3.76,3.542 2.563,0.302 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization may be needed. Refer to Calibration.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the spiral cable with sensor sub-assembly connector.


b.
E360126C01
1.469,0.385 1.927,0.656 0.458,0.271 1.135,1.875 1.354,1.375 true 1.583,0.438 2.042,0.635 0.458,0.198 10 false F69 0.146,0.167 0.604,0.365 0.458,0.198 10 false *a 0.979,1.927 1.438,2.125 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-1 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY AUXILIARY BATTERY POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY AUXILIARY BATTERY POWER SUPPLY)
a.

Disconnect the spiral cable with sensor sub-assembly connector.


b.
E360126C03
1.469,0.385 1.927,0.656 0.458,0.271 1.125,1.875 1.344,1.375 true 2.323,1.865 2.052,1.385 true 1.583,0.438 2.042,0.635 0.458,0.198 10 false F69 0.146,0.167 0.604,0.365 0.458,0.198 10 false *a 0.969,1.927 1.427,2.125 0.458,0.198 10 false ESS 2.25,1.927 2.729,2.167 0.479,0.24 10 false BAT
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-5 (BAT) - F69-1 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY IG POWER SUPPLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY IG POWER SUPPLY)
a.

Disconnect the spiral cable with sensor sub-assembly connector.


b.
E360126C04
1.469,0.385 1.927,0.656 0.458,0.271 1.135,1.875 1.354,1.375 true 2.146,1.865 1.875,1.385 true 1.583,0.438 2.042,0.635 0.458,0.198 10 false F69 0.146,0.167 0.604,0.365 0.458,0.198 10 false *a 0.979,1.927 1.438,2.125 0.458,0.198 10 false ESS 2.104,1.927 2.563,2.125 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-4 (IG1) - F69-1 (ESS) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR