Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303872 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the spiral cable sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Removal/installation of the spiral cable with sensor sub-assembly Steering angle neutral point (Initialize intelligent clearance sonar system)
·

Simple intelligent parking assist system

·

Toyota parking assist-sensor system


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/o Steering Heater)

a.
B459843C01
1.417,1.135 0.729,1.021 true 0.469,0.906 0.677,1.125 0.208,0.219 10 true *a
*a Flat Cable


Check the flat cable shown in the illustration.

If the flat cable shown in the illustration is not visible, it is possible that the spiral cable with sensor sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.


Hide 84307 4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ Steering Heater)

a.
B459857C01
1.948,1.302 2.458,1.615 true 2.521,1.563 2.75,1.76 0.229,0.198 10 true *a
*a Flat Cable


Check the flat cable shown in the illustration.

If the flat cable shown in the illustration is not visible, it is possible that the spiral cable with sensor sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.


Hide 45287 5.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

Hide 84307 7.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the front wheels are aligned facing straight ahead.


d.
B454038C01
1.052,2.417 1.385,2.417 true 1.458,2.313 1.625,2.479 0.167,0.167 10 true *a
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect each connector from the spiral cable with sensor sub-assembly.


f.
B459844

Disengage the claws to remove the spiral cable with sensor sub-assembly.


Hide 84306 8.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in the center position of the steering sensor becoming misaligned. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly when removing the steering sensor from the spiral cable sub-assembly.



a.

When replacing the steering sensor:

i.
C238437

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before installing the steering sensor to the spiral cable sub-assembly.




ii.
B279788C05
0.948,0.74 1.844,0.365 true 0.99,1.271 1.823,1.76 true 1.844,0.25 2.01,0.469 0.167,0.219 10 false *a 1.844,1.688 2.042,1.896 0.198,0.208 10 false *a
*a Guide


Disengage the claws and pins, and remove the spiral cable sub-assembly from the steering sensor.

NOTICE:

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.