Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2016.10–2019.09
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1581  Assist Map Number Un-Writing  


DESCRIPTION

This DTC will be stored if the power steering ECU assembly determines that the assist map is not written in the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1581 Assist Map Number Un-Writing Assist map not written in power steering ECU assembly
·

CAN communication system

·

Hybrid vehicle control ECU

·

Main body ECU (Multiplex network body ECU)

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Assist Map Writing is performed or the power switch is turned on (IG) again -

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Related parts store information necessary for assist map writing.

Related Part:

·

Hybrid vehicle control ECU

·

Main body ECU (Multiplex network body ECU)

·

Skid control ECU (Mrake booster with master cylinder assembly)



PROCEDURE

1.PERFORM ASSIST MAP WRITING
a.

Perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 142 3

b.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
Result:
Result Proceed to
DTC C1581 is output. A
DTC C1581 is not output. B


NOTICE:

DTC C1581 is cleared after the assist map is written.




A

2.CHECK CAN COMMUNICATION SYSTEM

B

END

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

3.CHECK RELATED PART

B

3.CHECK RELATED PART
a.

Confirm if the related part has the correct part number.

Related Part Hybrid vehicle control ECU
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake booster with master cylinder assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL




Result:
Result Proceed to
The related part has the correct part number. A
The related part has an incorrect part number. B



A

4.CHECK FOR DTC

B

5.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
4.CHECK FOR DTC
a.

Select Health Check on the GTS screen and check if system DTCs of the related part are output.

HINT:

If system DTCs of the related part are stored, assist map writing to the power steering ECU assembly may not be performed properly.



Result:
Result Proceed to
System DTCs of the related part are output. A
System DTCs of the related part are not output. (for LHD) B
System DTCs of the related part are not output. (for RHD) C



A

REPAIR CIRCUIT INDICATED BY OUTPUT CODE

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY

5.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. (for LHD) B
DTCs are output. (for RHD) C



A

END

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY