Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2016.10–2019.09
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1582  Assist Map Number Mismatch  


DESCRIPTION

When an incorrect hybrid vehicle control ECU, main body ECU (multiplex network body ECU) or skid control ECU (brake booster with master cylinder assembly) is installed after the assist map has been written to the power steering ECU assembly, DTC C1582 is stored because the information stored in the power steering ECU assembly does not match the vehicle specifications.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1582 Assist Map Number Mismatch Assist map number mismatch
·

CAN communication system

·

Incorrect hybrid vehicle control ECU

·

Incorrect main body ECU (multiplex network body ECU)

·

Incorrect skid control ECU (brake booster with master cylinder assembly)

·

Power steering ECU assembly


EPS warning light: Does not come on Assist Map Writing is performed or the power switch is turned on (IG) again -

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Related parts store information necessary for assist map writing.

Related Part:

·

Hybrid vehicle control ECU

·

Main body ECU (Multiplex network body ECU)

·

Skid control ECU (Brake booster with master cylinder assembly)



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.CHECK RELATED PART

B

2.CHECK RELATED PART
a.

Check if the part below has been replaced with an incorrect part in the past.

Related Part Hybrid vehicle control ECU
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake booster with master cylinder assembly)

NOTICE:

When removing the related part to check it, be sure to follow the appropriate procedures and precautions.

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL




b.

When DTC C1582 is output and parts have not been exchanged, replace the power steering ECU assembly as it may have an internal malfunction.

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



Result:
Result Proceed to
The related part has an incorrect part number. A
The related part has the correct part number, or a related part and power steering ECU assembly have not been replaced. (for LHD) B
The related part has the correct part number, or a related part and power steering ECU assembly have not been replaced. (for RHD) C



A

3.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY

3.REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER
a.

Replace the related part with one that has the correct part number.

·

Skid control ECU (Brake booster with master cylinder assembly)

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. (for LHD) B
DTCs are output. (for RHD) C



A

END

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY