Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2016.10–2019.09
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

C360723E04
0.906,0.698 1.406,0.948 0.5,0.25 10 false CANH 0.917,1.406 1.417,1.656 0.5,0.25 10 false CANL 1.375,0.521 1.625,0.771 0.25,0.25 10 false 31 1.396,1.219 1.646,1.469 0.25,0.25 10 false 30 1.385,2.865 1.635,3.115 0.25,0.25 10 false 28 5.76,0.5 6.021,0.771 0.26,0.271 10 false 7 5.771,1.219 6.031,1.49 0.26,0.271 10 false 8 5.708,2.854 5.969,3.125 0.26,0.271 10 false 13 5.781,3.469 6.042,3.74 0.26,0.271 10 false 4 1.115,2.969 1.448,3.219 0.333,0.25 10 false TC 0.573,4.146 1.073,4.396 0.5,0.25 10 false F3 5.833,1.854 6.333,2.104 0.5,0.25 10 false F23 5.958,0.688 6.458,0.938 0.5,0.25 10 false CANH 5.958,1.385 6.458,1.635 0.5,0.25 10 false CANL 6.125,4.323 6.625,4.573 0.5,0.25 10 false DLC3 5.958,2.969 6.292,3.219 0.333,0.25 10 false TC 5.958,3.583 6.292,3.833 0.333,0.25 10 false CG 0.25,4.344 2.323,4.604 2.073,0.26 10 false Hybrid Vehicle Control ECU 6.177,4.135 6.677,4.385 0.5,0.25 10 false F41 5.823,2.01 6.823,2.427 1,0.417 10 false Power Steering ECU Assembly 2.781,3.708 4.781,3.958 2,0.25 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C326026C44
1.583,0.5 2.083,0.75 0.5,0.25 1.604,1.885 1.229,1.313 true 1.833,2.375 2.115,1.302 true 1.719,0.521 2.031,0.719 0.313,0.198 10 false F41 0.99,1.208 1.302,1.406 0.313,0.198 10 false CG 2.167,1.198 2.479,1.396 0.313,0.198 10 false TC 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F41-13 (TC) - F41-4 (CG) Power switch on (IG) 9 to 16 V



Result:
Proceed to
OK
NG



OK

3.REPLACE HYBRID VEHICLE CONTROL ECU

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU)
3.REPLACE HYBRID VEHICLE CONTROL ECU
a.
C326026C44
1.583,0.5 2.083,0.75 0.5,0.25 1.604,1.885 1.229,1.313 true 1.833,2.375 2.115,1.302 true 1.719,0.521 2.031,0.719 0.313,0.198 10 false F41 0.99,1.208 1.302,1.406 0.313,0.198 10 false CG 2.167,1.198 2.479,1.396 0.313,0.198 10 false TC 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Turn the power switch off.


b.

c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-13 (TC) - F3-28 (TC) Always Below 1 Ω
F41-13 (TC) or F3-28 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C326026C46
1.51,0.5 2.01,0.75 0.5,0.25 1.604,1.885 1.229,1.313 true 1.635,0.531 1.948,0.729 0.313,0.198 10 false F41 0.979,1.208 1.292,1.406 0.313,0.198 10 false CG 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F41-4 (CG) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

6.REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU

6.REPLACE HYBRID VEHICLE CONTROL ECU
a.
C326026C44
1.583,0.5 2.083,0.75 0.5,0.25 1.604,1.885 1.229,1.313 true 1.833,2.375 2.115,1.302 true 1.719,0.521 2.031,0.719 0.313,0.198 10 false F41 0.99,1.208 1.302,1.406 0.313,0.198 10 false CG 2.167,1.198 2.479,1.396 0.313,0.198 10 false TC 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Replace the Hybrid vehicle control ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY