The entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Precaution.
After repair, confirm that no DTCs are output.
Check that the function operates normally.
Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door RH unlocked
LOCK: Front door RH locked |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | UNLOCK or LOCK | UNLOCK: Front door LH unlocked
LOCK: Front door LH locked |
- |
| RR-Door Lock Pos SW | Rear door RH and Rear door LH unlock detection switch signal | ON or OFF | ON: Rear door RH or Rear door LH unlocked
OFF: Rear door RH and Rear door LH locked |
- |
| RL-Door Lock Pos SW | Rear door LH and Rear door RH unlock detection switch signal | ON or OFF | ON: Rear door LH or Rear door RH unlocked
OFF: Rear door LH and Rear door RH locked |
- |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
The GTS display changes correctly in response to the lock/unlock operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not sound | A |
| Wireless door lock buzzer sounds | B |
A
B
Disconnect the A24 wireless door lock buzzer connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |
| Tester Display |
|---|
| Wireless Buzzer |
| *a | Front view of wire harness connector
(to Wireless Door Lock Buzzer) |
While performing the Active Test, measure the voltage between the terminals of the wireless door lock buzzer.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-1 (B) - A24-2 (E) | Active Test Wireless Buzzer ON | Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V) |
| Active Test Wireless Buzzer OFF | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the A24 wireless door lock buzzer connector.
Reconnect the 3F instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-1 (B) - MB-21 (BZR) | Always | Below 1 Ω |
| A24-2 (E) - Body ground | Always | Below 1 Ω |
| A24-1 (B) or MB-21 (BZR) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the 3F instrument panel junction block assembly connector.
Disconnect the A24 wireless door lock buzzer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-1 (B) - 3F-29 | Always | Below 1 Ω |
| A24-1 (B) or 3F-29 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C