The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
*1, *2, *3 |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| RR-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal | ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
*4, *5 |
| RL-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal | ON or OFF | ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked |
*4, *5 |
| Tester Display |
|---|
| FR Door Lock Pos |
| FL Door Lock Pos |
| RR-Door Lock Pos SW |
| RL-Door Lock Pos SW |
| Result | Proceed to |
|---|---|
| OK | A |
| "FL Door Lock Pos" is not normal | B |
| "FR Door Lock Pos" is not normal (*1, *2, *3) | C |
| Both "RL-Door Lock Pos SW" and "RR-Door Lock Pos SW" are not normal (*4, *5) | D |
*1: for RHD
*2: for LHD with Entry Function
*3: for LHD with Double Locking System
*4: w/ Entry Function
*5: w/ Double Locking System
A
B
C
D
Remove the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
Front door lock with motor assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J4-8 (LSSR) - 3D-13 | Always | Below 1 Ω |
| J4-8 (LSSR) or 3D-13 - Body ground | Always | 10 kΩ or higher |
| J4-7 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-13 - MB-19 (LSFL) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
Front door lock with motor assembly RH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-7 (LSSR) - 3D-12 | Always | Below 1 Ω |
| I4-7 (LSSR) or 3D-12 - Body ground | Always | 10 kΩ or higher |
| I4-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-12 - MB-17 (LSFR) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the rear door lock with motor assembly LH.
Inspect the rear door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
Rear door lock with motor assembly LH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L1-6 (LSSR) - 3D-14 | Always | Below 1 Ω |
| L1-6 (LSSR) or 3D-14 - Body ground | Always | 10 kΩ or higher |
| L1-9 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L1-5 (LSSR) - 3D-14 | Always | Below 1 Ω |
| L1-5 (LSSR) or 3D-14 - Body ground | Always | 10 kΩ or higher |
| L1-6 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door lock with motor assembly RH.
Inspect the rear door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>INSPECTION
Rear door lock with motor assembly RH is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-6 (LSSR) - 3D-14 | Always | Below 1 Ω |
| K1-6 (LSSR) or 3D-14 - Body ground | Always | 10 kΩ or higher |
| K1-9 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-9 (LSSR) - 3D-14 | Always | Below 1 Ω |
| K1-9 (LSSR) or 3D-14 - Body ground | Always | 10 kΩ or higher |
| K1-10 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-14 - MB-5 (LSR) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D