Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

Instrument panel junction block assembly

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the power switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).


HINT:

The power switch can be turned on (IG) and the hybrid control system can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

E352010E02
0.427,0.958 1.302,1.76 0.875,0.802 10 false from Auxiliary Battery 1.854,1.104 2.448,1.323 0.594,0.219 10 false AM2 2.333,0.865 2.927,1.083 0.594,0.219 10 false 4 2.573,0.958 3.167,1.177 0.594,0.219 10 false +B 2.604,1.656 3.198,1.875 0.594,0.219 10 false IC 2.271,2.281 2.865,2.5 0.594,0.219 10 false 18 2.573,2.375 3.167,2.594 0.594,0.219 10 false E 2.271,2.865 2.865,3.083 0.594,0.219 10 false F1 2.271,3.031 3.833,3.521 1.563,0.49 10 false Certification ECU (Smart Key ECU Assembly) 2.958,1.333 3.552,1.552 0.594,0.219 10 false +B 3.104,1.708 3.698,1.927 0.594,0.219 10 false ACCD 3.635,1.708 4.229,1.927 0.594,0.219 10 false 16 4.25,1.292 4.844,1.51 0.594,0.219 10 false 3K 4.25,1.813 4.844,2.031 0.594,0.219 10 false 3A 4.271,1.625 4.865,1.844 0.594,0.219 10 false 30 4.292,1.104 4.885,1.323 0.594,0.219 10 false 1 5.021,2.125 5.615,2.344 0.594,0.219 10 false ACC 4.083,2.49 6.99,2.927 2.906,0.438 10 false Instrument Panel Junction Block Assembly 5.573,1.427 6.5,1.656 0.927,0.229 10 false ECU-ACC 6.396,1.292 6.771,1.479 0.375,0.188 10 false 3A 6.396,1.813 6.771,2 0.375,0.188 10 false 3D 6.438,1.625 6.813,1.813 0.375,0.188 10 false 3 6.417,1.104 6.792,1.292 0.375,0.188 10 false 40

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A and 3D instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-16 (ACCD) - 3A-30 Always Below 1 Ω
3D-3 - Body ground Always Below 1 Ω
F1-16 (ACCD) or 3A-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

b.

Measure the resistance according to the value(s) in the table below.

B424436C09
5.313,0.167 5.813,0.417 0.5,0.25 2.167,0.167 2.667,0.417 0.5,0.25 3.375,1.542 3.875,1.792 0.5,0.25 0.188,0.146 0.5,0.344 0.313,0.198 10 false *a 2.344,0.188 2.656,0.385 0.313,0.198 10 false 3A 3.542,1.573 3.854,1.771 0.313,0.198 10 false 3D 5.479,0.198 5.792,0.396 0.313,0.198 10 false 3K
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-30 - 3D-3 20°C (68°F) 285.71 to 428.57 Ω
3K-1 - 3A-40 Auxiliary battery voltage not applied between terminals 3A-30 and 3D-3 10 kΩ or higher
Auxiliary battery voltage not applied between terminals 3A-30 and 3D-3 Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424427C35
1.521,0.083 2.021,0.333 0.5,0.25 0.896,1.917 1.281,0.979 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.698,0.104 2.052,0.365 0.354,0.26 10 false F1 0.438,1.823 0.938,2.063 0.5,0.24 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the F1 certification ECU (smart key ECU assembly) connector.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F1-16 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)