Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B228B  System Voltage or GND Energization Malfunction  


SYSTEM DESCRIPTION

This DTC is stored when there is a malfunction in the certification ECU (smart key ECU assembly) auxiliary battery power supply circuit or ground circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B228B System Voltage or GND Energization Malfunction Either of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*):
·

A malfunction is detected in the certification ECU (smart key ECU assembly) auxiliary battery power supply circuit.

·

A malfunction is detected in the certification ECU (smart key ECU assembly) ground circuit.


·

AM2 fuse

·

Wire harness or connector


DTC Output Confirmation Operation:

Drive the vehicle.



*: Only detected while a malfunction is present and the power switch is on (IG).


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Drive the vehicle. ○ ○
Malfunction Status A malfunction is detected in the certification ECU (smart key ECU assembly) auxiliary battery power supply circuit. ○ -
A malfunction is detected in the certification ECU (smart key ECU assembly) ground circuit. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The hybrid control system stopped while driving. -

Related Data List and Active Test Items
DTC No. Data List and Active Test
B228B -

WIRING DIAGRAM

B424433E12
1.979,0.531 3.49,0.927 1.51,0.396 10 false from Auxiliary Battery 4.385,0.688 5,0.885 0.615,0.198 10 false AM2 5.323,0.448 5.938,0.646 0.615,0.198 10 false 4 5.531,0.552 6.146,0.75 0.615,0.198 10 false +B 5.542,1.406 6.156,1.604 0.615,0.198 10 false E 5.26,1.292 5.875,1.49 0.615,0.198 10 false 18 5.198,1.906 5.813,2.104 0.615,0.198 10 false F1 5.198,2.052 6.719,2.51 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE