Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift lever in P and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Engine Start Request

·

S Code Check

·

L Code Check



WIRING DIAGRAM

E352029E02
0.458,1.104 0.771,1.302 0.313,0.198 10 false IC 0.469,2.135 0.781,2.333 0.313,0.198 10 false IC 0.458,4.406 0.771,4.604 0.313,0.198 10 false IC 0.896,0.813 1.208,1.01 0.313,0.198 10 false +B 0.896,1.583 1.208,1.781 0.313,0.198 10 false +B 1.292,1.188 1.604,1.385 0.313,0.198 10 false IGB 1.292,1.958 1.635,2.146 0.344,0.188 10 false ST2 1.188,4.313 1.573,4.479 0.385,0.167 10 false STP1 1.688,1.271 2,1.469 0.313,0.198 10 false F1 1.688,2.052 2,2.25 0.313,0.198 10 false F1 1.646,4.417 1.958,4.615 0.313,0.198 10 false M67 1.74,1.073 1.958,1.271 0.219,0.198 10 false 3 1.708,1.854 1.927,2.052 0.219,0.198 10 false 27 1.708,4.208 1.927,4.406 0.219,0.198 10 false 25 3.271,4.333 3.49,4.531 0.219,0.198 10 false 37 3.552,4.406 4.042,4.625 0.49,0.219 10 false STP2 3.573,4.813 3.885,5.01 0.313,0.198 10 false A39 5.646,1.281 5.958,1.479 0.313,0.198 10 false A48 5.688,2.052 6,2.25 0.313,0.198 10 false F2 5.635,2.76 5.948,2.958 0.313,0.198 10 false A49 6,1.177 6.313,1.375 0.313,0.198 10 false IGB 6,1.969 6.313,2.167 0.313,0.198 10 false ST2 6,2.76 6.313,2.958 0.313,0.198 10 false STP 5.719,1.083 5.938,1.281 0.219,0.198 10 false 7 5.719,1.875 5.938,2.073 0.219,0.198 10 false 9 5.677,2.583 5.896,2.781 0.219,0.198 10 false 15 5.906,3.229 6.833,3.677 0.927,0.448 10 false Hybrid Vehicle Control ECU 2.781,7.01 4.688,7.281 1.906,0.271 10 false Stop Light Switch Assembly 2.792,6.854 3.104,7.052 0.313,0.198 10 false A45 3.573,4.958 5.24,5.323 1.667,0.365 10 false Brake Booster with Master Cylinder Assembly 4.5,6.198 5,6.385 0.5,0.188 10 false STOP 4,6.031 4.24,6.229 0.24,0.198 10 false B 3.156,6.146 3.344,6.354 0.188,0.208 10 false L 3.51,6.26 3.823,6.458 0.313,0.198 10 false IC 3.823,6.458 4.24,6.656 0.417,0.198 10 false GND 4.219,5.948 4.438,6.146 0.219,0.198 10 false 7 4.229,6.365 4.448,6.563 0.219,0.198 10 false 2 2.979,6.146 3.198,6.344 0.219,0.198 10 false 3 5.469,6.031 7,6.354 1.531,0.323 10 false from Auxiliary Battery 0.156,5.167 1.688,5.625 1.531,0.458 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:
·

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

·

If the power switch is turned from on (IG) to on (ACC) with the shift lever in any position other than P, and then the shift lever is moved to P and the power switch is pressed with the brake pedal depressed, the power switch will turn off.



PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

12.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

Result:
Result Proceed to
"No" is displayed on the GTS screen A
"Yes" is displayed on the GTS screen B



A

3.CHECK WAVE ENVIRONMENT

B

REPLACE TRANSMITTER BATTERY

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.


OK:

Power source mode changes to on (READY).



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK POWER SWITCH CONDITION
4.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

5.READ VALUE USING GTS (SHIFT POSITION P)

B

C

D

5.READ VALUE USING GTS (SHIFT POSITION P)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR DTC

NG

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424427C37
1.542,0.083 1.958,0.333 0.417,0.25 1.302,0.844 0.667,1.875 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.667,0.125 1.979,0.281 0.313,0.156 10 false F1 0.396,1.781 0.896,2.021 0.5,0.24 10 false IGB
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-3 (IGB) - Body ground Power switch off → Power switch on (IG) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status OFF or ON OFF: The power switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the power switch is pressed and held
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

13.CHECK STEERING LOCK
10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F2 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-27 (ST2) - F2-9 (ST2) Always Below 1 Ω
F1-27 (ST2) or F2-9 (ST2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.
B424427C38
1.542,0.083 1.958,0.333 0.417,0.25 1.219,1.115 0.896,1.833 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.656,0.125 1.969,0.281 0.313,0.156 10 false F1 0.771,1.865 1.271,2.104 0.5,0.24 10 false ST2
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F1-27 (ST2) - Body ground Power switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after power switch released (starter off) 8.5 V or higher → 1.0 V or less



Result:
Proceed to
OK
NG



OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION

NOTICE:

Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

13.CHECK STEERING LOCK
a.

Check that the steering unlocks when the power switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

NG

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO IMMOBILISER SYSTEM (PROBLEM SYMPTOMS TABLE)

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SUPPLY AND BODY GROUND)
a.
B331566C84
0.323,0.958 0.823,1.208 0.5,0.25 1.156,1.823 1.385,1.354 true 2.573,1.813 2.448,1.344 true 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.01,1.844 1.406,2.063 0.396,0.219 10 false GND 0.448,1 0.844,1.219 0.396,0.219 10 false A45 2.563,1.833 2.958,2.052 0.396,0.219 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A45-7 (B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A45 stop light switch assembly connector.


c.

Disconnect the A49 hybrid vehicle control ECU connector.


d.

Disconnect the A39 brake booster with master cylinder assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-25 (STP1) - A45-3 (L) Always Below 1 Ω
M67-25 (STP1) or A45-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY