The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.
Disconnect the F50 radio and display receiver assembly connector.
Disconnect the S11 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-11 (CA+) - S11-6 (CB+) | Always | Below 1 Ω |
| F50-12 (V+) - S11-3 (CV+) | Always | Below 1 Ω |
| F50-24 (V-) - S11-2 (CV-) | Always | Below 1 Ω |
| F50-23 (CGND) - S11-5 (CGND) | Always | Below 1 Ω |
| F50-11 (CA+) or S11-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| F50-12 (V+) or S11-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| F50-24 (V-) or S11-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| F50-23 (CGND) or S11-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Remove the radio and display receiver assembly with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-23 (CGND) - Body ground | Always | Below 1 Ω |
| F50-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F50-11 (CA+) - Body ground | Power switch on (ACC) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Remove the radio and display receiver assembly with the connector connected.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
Waveform is as shown in the illustration.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | F50-12 (V+) - F50-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Power switch on (IG), shift lever in R, camera lens not covered, displaying an image
Waveform 2: Power switch on (IG), shift lever in R, camera lens covered, blacking out screen |
The video waveform changes according to the image sent by the rear television camera assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the radio and display receiver assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Check if the same malfunction recurs when the rear view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL