75431A
1.INSTALL NO. 1 BACK DOOR EMBLEM
75443
2.INSTALL NO. 3 BACK DOOR NAME PLATE
75442A
3.INSTALL NO. 2 BACK DOOR NAME PLATE
75441E
4.INSTALL NO. 1 BACK DOOR NAME PLATE (w/ Brand Mark)
5.INSTALL REAR LIGHT ASSEMBLY LH
6.INSTALL REAR LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
67894B
7.INSTALL NO. 2 BACK DOOR PANEL PROTECTOR
Clean vehicle installation surface.
Remove the release paper from a new No. 2 back door panel protector.
|
Double-sided Tape |
Engage the clips to install the No. 2 back door panel protector.
Press the double-sided tape area of the No. 2 back door panel protector.
67893A
8.INSTALL NO. 1 BACK DOOR PANEL PROTECTOR
Use the same procedure for the No. 2 back door panel protector.
67005B
9.INSTALL BACK DOOR PANEL CUSHION
Engage the claws to install the 2 back door panel cushions.
86790D
10.INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)
76827A
11.INSTALL NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)
Engage the claws to install the No. 2 back door garnish retainer.
81270
12.INSTALL LICENSE PLATE LIGHT ASSEMBLY
84840G
13.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY
14.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
85345R
15.INSTALL REAR WASHER NOZZLE (w/ Rear Wiper)
16.INSTALL REAR SPOILER ASSEMBLY
67282F
17.INSTALL BACK DOOR LOWER STOPPER
Engage the guide and install the back door lower stopper.
Install a new bolt.
Use the same procedure for the RH side and LH side.
85110R
18.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
85143R
19.INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)
20.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)
69350
21.INSTALL BACK DOOR LOCK ASSEMBLY
69321
22.INSTALL BACK DOOR LOCK COVER
Clean vehicle installation surface.
Remove the release paper from a new back door lock cover.
|
Double-sided Tape |
Engage the claws to install the back door lock cover.
Press the double-sided tape area of the back door lock cover.
67765A
23.INSTALL BACK DOOR SERVICE HOLE COVER LH
Engage the claws to install the back door service hole cover LH.
67765A
24.INSTALL BACK DOOR SERVICE HOLE COVER RH
Use the same procedure as for the LH side.
67765A
25.INSTALL NO. 3 BACK DOOR SERVICE HOLE COVER
Engage the claws to install the No. 3 back door service hole cover.
67765A
26.INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER
Use the same procedure as for the No. 1 back door service hole cover.
67765A
27.INSTALL NO. 1 BACK DOOR SERVICE HOLE COVER
Engage the claws to install the No. 1 back door service hole cover.
74811B
28.INSTALL DOOR PULL HANDLE
Engage the claws to install the door pull handle as shown in the illustration.
Full open the back door, and ensure that the arrow provided on the back of the door pull handle is facing upward.
64780A
29.INSTALL BACK DOOR TRIM PANEL ASSEMBLY
Engage the clips to install the back door trim panel assembly.
64338D
30.INSTALL PACKAGE TRAY TRIM GARNISH HOOK
Use the same procedure for the RH side and LH side.
Install the package tray trim garnish hook.
Install the screw.
67938A
31.INSTALL BACK DOOR SIDE GARNISH LH
Engage the claws and clips to install the back door side garnish LH.
67937B
32.INSTALL BACK DOOR SIDE GARNISH RH
Use the same procedure as for the LH side.
64790B
33.INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY
Engage the claws and clips to install the back door trim upper panel assembly.
64910J
34.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
64330D
35.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)