89342B
1.REMOVE REAR SIDE ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342
2.REMOVE REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342A
3.REMOVE REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89348T
4.REMOVE REAR SIDE ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89348R
5.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89348S
6.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
82169A
7.REMOVE NO. 6 FLOOR WIRE
w/ TOYOTA Parking Assist-sensor System and Rear Fog Light:
Disengage the clamps to remove the No. 6 floor wire.
Disconnect the connector.
w/ Rear Fog Light:
Disengage the clamps to remove the No. 6 floor wire.
Disconnect the connector.
81480B
8.REMOVE REAR FOG LIGHT ASSEMBLY
Remove the 2 screws and rear fog light.
52166A
9.REMOVE REAR BUMPER UPPER COVER LH
Disengage the hook to remove the rear bumper upper cover LH.
52165A
10.REMOVE REAR BUMPER UPPER COVER RH
Use the same procedure as for the LH side.
81920
11.REMOVE REFLEX REFLECTOR ASSEMBLY LH
|
Remove in this Direction |
Remove the screw.
Disengage the claw and guide to remove the reflex reflector assembly LH as shown in the illustration.
81910
12.REMOVE REFLEX REFLECTOR ASSEMBLY RH
Use the same procedure as for the LH side.
52164A
13.REMOVE REAR BUMPER PLATE LH
|
Remove in this Direction |
Remove the 2 screws.
Disengage the claws to remove the rear bumper plate LH as shown in the illustration.
52163A
14.REMOVE REAR BUMPER PLATE RH
Use the same procedure as for the LH side.
52756
15.REMOVE REAR BUMPER MOULDING RETAINER LH (w/ Rear Bumper Moulding Retainer)
| *1 | Outside Moulding Retainer |
Remove the 2 nuts.
Remove the outside moulding retainer.
Remove the No. 2 rear bumper side retainer LH and rear bumper moulding retainer LH with No. 1 rear spoiler protector.
Remove the No. 1 rear spoiler protector from the rear bumper moulding retainer LH.
52755
16.REMOVE REAR BUMPER MOULDING RETAINER RH (w/ Rear Bumper Moulding Retainer)
Use the same procedure as for the LH side.
52162B
17.REMOVE NO. 1 REAR BUMPER PLATE
Disengage the claws.
Disengage the hook to remove the No. 1 rear bumper plate.
52461F
18.REMOVE REAR BUMPER PAD
Remove the rear bumper pad.
52463
19.REMOVE REAR BUMPER PAD LH
Remove the rear bumper pad LH.
52462
20.REMOVE REAR BUMPER PAD RH
Use the same procedure as for the LH side.
52154B
21.REMOVE REAR BUMPER SIDE STAY LH
|
Remove in this Direction |
Remove the clip and screw.
Disengage the claw to remove the rear bumper side stay LH as shown in the illustration.
52153A
22.REMOVE REAR BUMPER SIDE STAY RH
Use the same procedure as for the LH side.
52453
23.REMOVE REAR BUMPER CENTER GUARD
Remove the 2 clips and 6 outside moulding retainers.
| *a | Clip | *b | Outside Moulding Retainer |
Disengage the claws and guides to remove the rear bumper center guard.
52576B
24.REMOVE REAR BUMPER SIDE RETAINER LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 2 screws.
Disengage the claw and guide to remove the rear bumper side retainer LH as shown in the illustration.
52575
25.REMOVE REAR BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
52563A
26.REMOVE REAR BUMPER UPPER RETAINER LH
|
Remove in this Direction |
Remove the claws and rear combination light cover LH as shown in the illustration.
| *a | Guide |
| *b | Pin |
|
Remove in this Direction |
Remove the 3 screws.
Disengage the pin and guide as shown in the illustration.
Disconnect the connector to remove the combination light assembly LH.
|
Remove in this Direction |
Disengage the guides to remove the rear bumper upper retainer LH as shown in the illustration.
52562B
27.REMOVE REAR BUMPER UPPER RETAINER RH
Use the same procedure as for the LH side.
52023
28.REMOVE REAR BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type A)
Remove the 8 bolts and rear bumper reinforcement sub-assembly.
52015A
29.REMOVE REAR BUMPER ARM SUB-ASSEMBLY RH (for Type B)
Remove the 4 bolts and rear bumper arm sub-assembly.