Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door) › 2016.10–2020.08
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304194 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75988E 2.INSTALL REAR DOOR OUTSIDE STRIPE

a.

Refer to the illustration to position a new rear door outside stripe.

B458794C01
4.75,1.052 5,1.219 false 6.51,2.167 6.76,2.25 false 5.469,3.25 5.719,3.167 false 5.688,1.104 5.938,1.271 false 4.417,2 4.667,2.083 false 5.25,1.656 5.5,1.896 0.25,0.24 12 false *A 5.25,2.75 5.563,3 0.313,0.25 12 false *B 1.219,0.385 1.531,0.542 0.313,0.156 10 false *a 4.219,1.896 4.531,2.052 0.313,0.156 10 false *b 4.563,0.938 4.875,1.094 0.313,0.156 10 false *c 6.833,2.146 7.146,2.302 0.313,0.156 10 false *d 5.313,3.146 5.625,3.302 0.313,0.156 10 false *e 4.396,0.167 4.771,0.438 0.375,0.271 10 false a-a 5.896,1.271 6.208,1.427 0.313,0.156 10 false *c 1.01,1.229 1.156,1.396 0.146,0.167 10 true A 2.917,1.302 3.073,1.5 0.156,0.198 10 false B 4.563,1.271 4.719,1.469 0.156,0.198 10 false C 6.052,0.896 6.208,1.094 0.156,0.198 10 false D 1.854,1.729 2.167,1.885 0.313,0.156 10 false a 1.896,2.344 2.208,2.5 0.313,0.156 10 false a
*A LH Side *B RH Side
*a Point A *b Point B
*c Edge of Curved Surface *d Straight
*e Triangle - -


Standard Measurement:
Area Measurement Area Measurement
A 1.0 mm (0.0394 in.) B 10.0 mm (0.394 in.)
C 1.0 mm (0.0394 in.) D 2.5 mm (0.0984 in.)



b.

Remove the release paper and install the rear door outside stripe.

HINT:

Align the point (B) on the rear door outside stripe with the point (A) on the door frame and install the rear door outside stripe.



Hide 75978H 3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE

a.

Refer to the illustration to position a new rear door lower outside stripe.

B458795C01
6,1.906 5.75,1.823 false 3.75,1.208 3.333,1 true 5.25,2.427 5,2.26 false 6.667,2.26 6.417,2.427 false 5.448,2.521 5.198,2.688 false 6.5,2.688 6.25,2.521 false 4.573,2.24 4.823,2.479 0.25,0.24 12 false *A 5.917,2.25 6.229,2.5 0.313,0.25 12 false *B 3.135,0.906 3.448,1.063 0.313,0.156 10 false *a 5.031,2.594 5.344,2.75 0.313,0.156 10 false *b 6.073,1.823 6.385,1.979 0.313,0.156 10 false *c 4.802,2.167 5.115,2.323 0.313,0.156 10 false *d 6.729,2.167 7.042,2.323 0.313,0.156 10 false *e 4.823,0.25 5.115,0.438 0.292,0.188 10 false a-a 3.25,1.302 3.406,1.5 0.156,0.198 10 false A 3.073,2.938 3.24,3.104 0.167,0.167 10 true B 4.885,0.979 5.042,1.177 0.156,0.198 10 false C 5.688,2.146 5.844,2.344 0.156,0.198 10 false D 6.552,2.594 6.865,2.75 0.313,0.156 10 false *b 2.948,2.042 3.26,2.198 0.313,0.156 10 false a 2.323,2.115 2.469,2.281 0.146,0.167 10 true a
*A LH Side *B RH Side
*a Point A *b Point B
*c Edge of Curved Surface *d Straight
*e Triangle - -


Standard Measurement:
Area Measurement Area Measurement
A 10.0 mm (0.394 in.) B 5.0 mm (0.197 in.)
C -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) D 1.0 mm (0.0394 in.)



b.

Remove the release paper and install the rear door lower outside stripe.

HINT:

Align the point (B) on the rear door lower outside stripe with the point (A) on the door frame and install the rear door lower outside stripe.



Hide 68124B 4.INSTALL REAR DOOR QUARTER WINDOW GLASS

Hide 68152C 5.INSTALL REAR DOOR GLASS RUN

Hide 67674A 6.INSTALL REAR DOOR FRAME GARNISH

Hide 68104 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67408F 8.INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

Hide 67872 9.INSTALL REAR DOOR WEATHERSTRIP

Hide 67842E 10.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 68197 11.INSTALL REAR DOOR BELT SEAL

Hide 68174A 12.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68199 13.INSTALL REAR DOOR BELT REAR SEAL

Hide 67604 14.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67498 15.INSTALL REAR DOOR REAR FRAME BRACKET

Hide 74272A 16.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 69284D 17.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 18.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 19. INITIALIZE POWER WINDOW CONTROL SYSTEM