Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise SET Indicator Light Circuit  


DESCRIPTION

The hybrid vehicle control ECU illuminates the cruise control SET indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control SET indicator illuminates when the dynamic radar cruise control system is controlling vehicle speed. The cruise SET indicator light circuit uses CAN communication. If the cruise control SET indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.

CAUTION / NOTICE / HINT

CAUTION:

Observe the following items for safety reasons when using GTS:

·

Before using the GTS, read the instruction GTS.

·
A356952

Prevent the GTS cable from being caught on the pedals, shift lever or steering wheel when driving with the GTS connected to the vehicle.

·
A356953

When driving the vehicle for testing purposes, 2 people are required. One person should operate the GTS while the other drives the vehicle.



NOTICE:
·

Before replacing the hybrid vehicle control ECU refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>COMPONENTS



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Meter Display 1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF, 6 to 0 or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

2.READ VALUE USING GTS (-SET SWITCH)

B

2.READ VALUE USING GTS (-SET SWITCH)
a.

Turn the cruise control system on using the cruise control main switch (ON/OFF button).


b.

Drive at a speed between approximately 0 km/h (0 mph) and 180 km/h (110 mph).


c.

Enter the following menus: Powertrain / Cruise Control / Data List.


d.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
-SET Switch
50003 399 22

Result:
Result Proceed to
The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-SET switch). A
The cruise control SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the cruise control main switch (-SET switch). B
The cruise control SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the cruise control main switch (-SET switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C