The forward recognition camera receives vehicle stability signals from the yaw rate and acceleration sensor (airbag sensor assembly). If the yaw rate and acceleration sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA4 | Yaw Rate Sensor Circuit | 3 seconds after the power switch is turned on (IG), a signal from the yaw rate sensor indicating a malfunction in the yaw rate and acceleration sensor (airbag sensor assembly) is detected by the forward recognition camera for 5 seconds or more. | ·
Electronically controlled brake system ·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Forward recognition camera |
| C1AA5 | Yaw Rate Sensor Power Supply Voltage Circuit | 3 seconds after the power switch is turned on (IG), a signal from the yaw rate sensor indicating an abnormal yaw rate and acceleration sensor (airbag sensor assembly) power supply voltage signal is detected by the forward recognition camera for 5 seconds or more. | ·
Electronically controlled brake system ·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Forward recognition camera system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTCs are not output | A |
| Electronically controlled brake system DTCs are output | B |
A
B
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA4 and C1AA5 are not output | A |
| DTC C1AA4 or C1AA5 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform Forward Recognition Camera Axis Adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA4 and C1AA5 are not output | A |
| DTC C1AA4 or C1AA5 is output | B |
A
B