Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304573 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The forward recognition camera receives vehicle stability signals from the yaw rate and acceleration Sensor (airbag sensor assembly). If the yaw rate and acceleration Sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor assembly power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit 2 seconds after the power switch is turned on (IG), the vehicle speed is 5 km/h or more and a signal from the yaw rate sensor indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more.
·

Electronically controlled brake system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Forward recognition camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit 2 seconds after the power switch is turned on (IG), the vehicle speed is 5 km/h or more and a signal from the yaw rate sensor indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more.
·

Electronically controlled brake system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK DTC OUTPUT (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

If the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the electronically controlled brake system will be stored. Troubleshoot the electronically controlled brake system first.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK DTC OUTPUT

B

2.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.


e.

f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.

2.

Drive the vehicle at 5 km/h (3 mph) or more.




g.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AA4 or C1AA5 is output. A
DTC C1AA4 and C1AA5 are not output. B



A

3.REPLACE FORWARD RECOGNITION CAMERA

B

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.


e.

f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 7 seconds or more.

2.

Drive the vehicle at 5 km/h (3 mph) or more.




g.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AA4 or C1AA5 is output. A
DTC C1AA4 and C1AA5 are not output. B



A

REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)