Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0304576 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn assembly to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

E352024E02
0.125,1.823 1.042,2.292 0.917,0.469 10 false from Auxiliary Battery 1.406,1.979 2.052,2.188 0.646,0.208 10 false S-HORN 2.594,2.646 3.24,2.854 0.646,0.208 10 false S-HORN 2.979,3.781 3.323,3.99 0.344,0.208 10 false A15 2.969,3.948 4.521,4.177 1.552,0.229 10 false Security Horn Assembly 3.448,3.323 3.667,3.531 0.219,0.208 10 false 1 3.833,3.406 4.052,3.615 0.219,0.208 10 false 2 3.313,1.719 3.531,1.927 0.219,0.208 10 false 2 2.396,2.229 2.615,2.438 0.219,0.208 10 false 5 3.323,2.229 3.542,2.438 0.219,0.208 10 false 3 2.375,1.719 2.594,1.927 0.219,0.208 10 false 1 4.281,1.625 4.5,1.833 0.219,0.208 10 false 20 5.604,1.635 5.823,1.844 0.219,0.208 10 false 29 4.271,1.844 4.542,2.052 0.271,0.208 10 false 3A 5.583,1.844 5.854,2.052 0.271,0.208 10 false MB 5.969,1.74 6.24,1.948 0.271,0.208 10 false SH 6.552,1.854 6.823,2.063 0.271,0.208 10 false IC 4.26,2.813 5.865,3.219 1.604,0.406 10 false Instrument Panel Junction Block Assemb 5.458,3.531 7.104,3.917 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn Assembly OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.

Remove the S-HORN relay from the No. 4 relay block assembly.



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).


E352025C01
3.25,0.25 3.75,0.5 0.5,0.25 3.25,1.75 3.75,2 0.5,0.25 4.844,2.313 5.219,2.625 true 0.177,0.156 0.49,0.313 0.313,0.156 10 false *a 3.417,0.281 3.729,0.438 0.313,0.156 10 false 3A 3.385,1.781 3.698,1.938 0.313,0.156 10 false MB 5.26,2.531 5.573,2.688 0.313,0.156 10 false SH
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-20 - MB-29 (SH) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)
a.

Remove the S-HORN relay from the No. 4 relay block assembly.


b.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 4 Relay Block Assembly


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
No. 4 relay block assembly S-HORN relay terminal 1 - Body ground Power switch off 11 to 14 V
No. 4 relay block assembly S-HORN relay terminal 5 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.

Remove the S-HORN relay from the No. 4 relay block assembly.


b.

Disconnect the A15 security horn assembly connector.


c.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 4 Relay Block Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 relay block assembly S-HORN relay terminal 3 - A15-1 Always Below 1 Ω
No. 4 relay block assembly S-HORN relay terminal 3 or A15-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the S-HORN relay from the No. 4 relay block assembly.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 4 Relay Block Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 relay block assembly S-HORN relay terminal 2 - 3A-20 Always Below 1 Ω
No. 4 relay block assembly S-HORN relay terminal 2 or 3A-20 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR