Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0304576 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Improper Operation  


DESCRIPTION

When the auto alarm system operates by itself, it could be due to a misdetection by the theft warning radar sensor (intrusion sensor), or by something such as a short circuit in the courtesy light switch of any of the doors or the hood causing a signal to be sent in error.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.

·

The driver locks the doors and walks away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

A window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car wash.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



HINT:

Preconditions for Arming Preparation:

·

The power switch is off and all the doors and the hood are closed and all doors are locked by wireless operation or entry operation*1.

*1: w/ Entry Function




CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The theft deterrent system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the theft deterrent system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.

·

The function "Read operation history" uses the current system time setting inside the GTS and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the GTS system clock is accurately set to the current time.



PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CONFIRMATION
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past the hybrid control system isstarted problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in the problem analysis:

What? Vehicle model, system name
When? Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where? Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the power switch was on, whether the hybrid control system was starting
How did it happen? Problem symptoms*

-

*: Be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem, and then check for DTCs.




Result:
Proceed to
NEXT



2.CHECK FOR DTC*
2.CHECK FOR DTC*
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
NOTICE:

After problem symptoms have occurred, do not disconnect the auxiliary battery until after the DTC checks have been performed.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK THEFT DETERRENT SYSTEM OPERATION HISTORY

B

3.CHECK THEFT DETERRENT SYSTEM OPERATION HISTORY
a.

Use the GTS to check the theft deterrent system operation history around the time that the malfunction reported by the customer occurred, based on the contents of the customer interview and the last recorded theft deterrent system operation history around the time that the problem is reported to have occurred.

i.

On the GTS screen, enter the following menus: Body / Main Body / Utility / Operation History Analysis. According to the display on the GTS, read the operation history.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>OPERATION HISTORY LIST


ii.

Check that there is theft deterrent system operation history as reported by the customer.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>OPERATION HISTORY LIST

HINT:

Based on the displayed operation history, perform vehicle-side inspection, and perform repairs if a problem is found. If the vehicle has no malfunction, interview the customer about possible causes such as "the driver" and "environmental / other than the driver".




Result:
Result Proceed to
There is operational history around the time that the customer reported the malfunction to have occurred, but the malfunction could not be identified even by following the instructions to inspect the relevant areas A
There is operational history around the time that the customer reported the malfunction to have occurred, and by following the instructions to inspect the relevant areas, the malfunction was identified B
There is no operational history around the time that the customer reported the malfunction to have occurred. C



A

4.CHECK SECURITY INDICATOR LIGHT OPERATION

B

19.INTERVIEW THE CUSTOMER

C

END

4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the theft deterrent system is in arming preparation state, check that the security indicator light is illuminated.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION


b.

When the theft deterrent system is in armed state, check that the security indicator light blinks.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

HINT:
State of Theft Deterrent System Contents Security Indicator Light Condition
Disarmed state (1), (2) Theft deterrent system is unset.
·

Off (Immobiliser system unset)

·

Blinking (Immobiliser system set)


Arming preparation state Standby period after theft deterrent system set conditions are met but before theft deterrent system is actually set (approximately 30 seconds).
(Theft detection not performed)
On
Armed state Theft deterrent system is unset.
(Theft detection is possible)
Blinking (Immobiliser system set)
Alarm sounding state Theft attempt is detected, and alarm is sounded using turn signal light, security horn assembly*1, theft warning siren assembly*2, and vehicle horn.
(Alarm sounds for 27.5 seconds)
On

*1: w/o Intrusion Sensor

*2: w/ Intrusion Sensor




Result:
Result Proceed to
OK (w/ Intrusion Sensor) A
OK (w/o Intrusion Sensor) B
NG C



A

5.READ VALUE USING GTS (Intrusion Sens OFF SW)

B

7.READ VALUE USING GTS

C

5.READ VALUE USING GTS (Intrusion Sens OFF SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sens OFF SW
50003 123 203
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (INTRUSION SENSOR, INTRUSION SENSOR SOUND DETECT)

NG

17.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR CANCEL SWITCH (MAP LIGHT ASSEMBLY) - BODY GROUND)
6.READ VALUE USING GTS (INTRUSION SENSOR, INTRUSION SENSOR SOUND DETECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

HINT:

When performing the above inspection, have the electrical key transmitter sub-assembly in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


NOTICE:

Make sure that all windows are closed.



f.

Make a metal-on-metal striking sound (such as by shaking keys) near the intrusion sensor (theft warning ultrasonic sensor) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Sound Detect Sound detection status of the intrusion sensor (theft warning ultrasonic sensor)*1 ON or OFF ON: Sound detected
OFF: Sound not detected
Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor Sound Detect
50003 123 273
NOTICE:

*1: Perform the intrusion sensor (theft warning ultrasonic sensor) operation inspection with the GTS disconnected.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION



g.

From inside the vehicle, put your hand in front of the intrusion sensor (theft warning ultrasonic sensor) and move it back and forth a distance of 0.7 to 1 m (2.30 to 3.28 ft.) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Detection status of the intrusion sensor (theft warning ultrasonic sensor) ON or OFF ON: Intrusion detected
OFF: Intrusion not detected
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204

OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

15.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Power switch ACC signal ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW Power switch ON signal ON or OFF ON: Power switch on (IG)
OFF: Power switch off or on (ACC)
-
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS

NG

8.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52

Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS

NG

9.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF ON: Front door RH open
OFF: Front door RH closed
-
FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 24,25,197,199
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS

NG

10.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy light switch ON or OFF ON: Back door open
OFF: Back door closed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Courtesy SW
50003 123 26
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (HOOD COURTESY SW)

NG

11.READ VALUE USING GTS (HOOD COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy SW Hood courtesy switch ON or OFF ON: Hood open
OFF: Hood closed
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy SW
50003 123 200
OK:

The GTS display changes correctly in response to the hood courtesy switch (hood lock assembly) status.



Result:
Proceed to
OK
NG



OK

12.INTERVIEW THE CUSTOMER

NG

13.INSPECT HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
12.INTERVIEW THE CUSTOMER
a.

If the phenomenon could not be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electrical key transmitter sub-assembly (electronic key) for the relevant date/time in the operation history.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


Standard:

Cause was identified


Result:
Proceed to
OK
NG



OK

END

NG

13.INSPECT HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.

Remove the hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

REPLACE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

14.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A8 hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-11 (HCTY) - A8-1 (+) Always Below 1 Ω
F15-11 (HCTY) or A8-1 (+) - Body ground Always 10 kΩ or higher
A8-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
a.

Using an oscilloscope, check the waveform.

E352022C01
3.5,0.292 3.948,0.542 0.448,0.25 4.281,1.875 3.771,1.385 true 1.906,2.823 1.594,2.708 false 2.438,2.854 2.229,2.708 false 3.594,0.323 3.938,0.542 0.344,0.219 10 false R10 2.427,0.354 2.688,0.583 0.26,0.229 10 false *a 1.406,2.615 1.698,2.833 0.292,0.219 10 false *b 2.052,2.615 2.323,2.844 0.271,0.229 10 false *c 3.99,2.625 4.302,2.781 0.313,0.156 10 false *d 3.99,3.156 4.302,3.313 0.313,0.156 10 false *e 2.115,3.219 2.385,3.438 0.271,0.219 10 false *f 2.51,3.198 2.813,3.417 0.302,0.219 10 false *g 2.667,3.625 2.979,3.781 0.313,0.156 10 false *h 1.51,4.135 1.792,4.365 0.281,0.229 10 false *i 4,4.125 4.313,4.354 0.313,0.229 10 false *j 4.375,1.813 4.823,2.01 0.448,0.198 10 false IOUT 1,2.479 1.292,2.698 0.292,0.219 10 false HI 1,2.917 1.292,3.135 0.292,0.219 10 false LO
*a Component with harness connected
(Intrusion Sensor (Theft Warning Ultrasonic Sensor))
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 Second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 Seconds
*g Approximately 0.05 Seconds *h Approximately 5.5 Seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition:
Item Content
Tester Connection R10-2 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)


HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform is output properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the F16 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R10 intrusion sensor (theft warning ultrasonic sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-12 (ISIF) - R10-2 (IOUT) Always Below 1 Ω
F16-12 (ISIF) or R10-2 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR CANCEL SWITCH (MAP LIGHT ASSEMBLY) - BODY GROUND)
a.

Disconnect the F16 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R2 intrusion sensor cancel switch (map light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (SSW1) - R2-11 (SOFF) Always Below 1 Ω
F16-13 (SSW1) or R2-11 (SOFF) - Body ground Always 10 kΩ or higher
R2-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT INTRUSION SENSOR CANCEL SWITCH (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT INTRUSION SENSOR CANCEL SWITCH (MAP LIGHT ASSEMBLY)
a.

Remove the intrusion sensor cancel switch (map light assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the intrusion sensor cancel switch (map light assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INTRUSION SENSOR CANCEL SWITCH (MAP LIGHT ASSEMBLY)

19.INTERVIEW THE CUSTOMER
a.

If the phenomenon could not be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electrical key transmitter sub-assembly (electronic key) for the relevant date/time in the operation history.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


Standard:

Cause was identified


Result:
Proceed to
OK
NG



OK

END

NG