Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062180 METER / GAUGE / DISPLAY _0304590 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter assembly receives a text data signal from the radio and display receiver assembly via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly when the power switch is on (ACC), 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.
·

Harness or connector

·

Radio and display receiver assembly

·

Combination meter assembly


DTC stored -

WIRING DIAGRAM

E361276E02
1,2.385 3.052,2.594 2.052,0.208 10 false : AVC-LAN Communication Line 1.771,0.719 2.385,0.917 0.615,0.198 10 false CNL1 1.75,1.271 2.365,1.469 0.615,0.198 10 false CNH1 2.24,0.583 2.396,0.781 0.156,0.198 10 false 4 2.24,1.135 2.396,1.333 0.156,0.198 10 false 3 0.979,1.74 1.438,1.938 0.458,0.198 10 false F50 0.979,1.896 2.708,2.313 1.729,0.417 10 false Radio and Display Receiver Assembly 5.146,0.708 5.76,0.906 0.615,0.198 10 false MSCL 5.146,1.26 5.76,1.458 0.615,0.198 10 false MSCH 4.875,0.583 5.188,0.781 0.313,0.198 10 false 37 4.875,1.135 5.188,1.333 0.313,0.198 10 false 36 4.635,1.74 4.948,1.938 0.313,0.198 10 false F4 4.625,1.906 6.552,2.125 1.927,0.219 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK FOR DTC
a.

Check if audio and visual system DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

Audio and visual system DTCs are not output.



Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the F50 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-37 (MSCL) - F50-4 (CNL1) Always Below 1 Ω
F4-36 (MSCH) - F50-3 (CNH1) Always Below 1 Ω
F4-37 (MSCL) - Body ground Always 10 kΩ or higher
F4-36 (MSCH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B



A

END

B