Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B162B/85  Side Airbag Sensor Assembly No.2 Lost Communication (RH)  B162C/85  Side Airbag Sensor Assembly No.2 Initialization Error (RH)  


DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and floor side airbag sensor RH.

The floor side airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B162B/85 Side Airbag Sensor Assembly No.2 Lost Communication (RH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2).

·

Floor side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B162C/85 Side Airbag Sensor Assembly No.2 Initialization Error (RH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2).

·

Floor side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B162B/85):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2) - - - ○ - -
Floor side airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B162C/85):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 2) - - - ○ - -
Floor side airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C303969E30
5.323,2.885 6.938,3.198 1.615,0.313 10 false Airbag Sensor Assembly 5.323,2.719 6.917,2.917 1.594,0.198 10 false M17*1, M18*2 4.615,0.802 5.521,1 0.906,0.198 10 false 15*1, 20*2 4.625,1.771 5.573,2 0.948,0.229 10 false 14*1, 19*2 5.375,0.906 6.094,1.302 0.719,0.396 10 false BCR+ 5.375,1.875 6.094,2.271 0.719,0.396 10 false BCR- 1.406,0.906 2.125,1.302 0.719,0.396 10 false BFR+ 1.427,1.875 2.146,2.271 0.719,0.396 10 false BFR- 1.844,0.802 2.563,1.198 0.719,0.396 10 false 2 1.844,1.781 2.563,2.177 0.719,0.396 10 false 1 0.563,2.719 2.125,3.333 1.563,0.615 10 false M34 0.563,2.885 2.125,3.24 1.563,0.354 10 false Floor Side Airbag Sensor RH 3.083,3.031 5.635,3.281 2.552,0.25 10 false *1: w/o Dual-stage SRS 3.083,3.375 5.635,3.625 2.552,0.25 10 false *2: w/ Dual-stage SRS

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and floor side airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and floor side airbag sensor RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
C341895C05
0.833,0.5 1.25,0.75 0.417,0.25 0.583,3.583 1,3.833 0.417,0.25 1.625,2.521 1.625,1.938 1.625,1.938 1.375,1.938 false 1.833,1.375 1.833,1.167 false 1.458,1.24 1.771,0.875 true 2.198,1.229 1.885,0.875 true 1.052,4.229 1.406,3.729 true 2.01,4.24 1.688,3.729 true 0.667,2.5 1.094,2.896 0.427,0.396 10 false *1 2.552,2.229 2.979,2.781 0.427,0.552 10 false *2 1.219,1.865 1.698,2.281 0.479,0.417 10 false *3 1.771,1.406 2.104,1.74 0.333,0.333 10 false *4 0.688,0.177 1.073,0.458 0.385,0.281 10 false *a 0.427,3.25 0.833,3.76 0.406,0.51 10 false *b 2.083,1.25 2.583,1.594 0.5,0.344 10 false BCR+ 1.292,1.25 1.792,1.594 0.5,0.344 10 false BCR- 0.917,0.542 1.417,0.885 0.5,0.344 10 false M18 2.188,2.5 2.615,3.052 0.427,0.552 10 false A 1.885,2.5 2.313,3.052 0.427,0.552 10 false B 1.292,2.5 1.719,3.052 0.427,0.552 10 false C 0.979,2.5 1.406,3.052 0.427,0.552 10 false D 0.667,3.625 1.167,3.969 0.5,0.344 10 false M34 1.875,4.25 2.375,4.594 0.5,0.344 10 false BFR+ 0.906,4.25 1.406,4.594 0.5,0.344 10 false BFR-
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Using a service wire, connect terminals 20 (BCR+) and 19 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - M34-1 (BFR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - M34-1 (BFR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch off.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M34-2 (BFR+) - Body ground Power switch on (IG) Below 1 V
M34-1 (BFR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C341628C05
0.583,2.25 1,2.5 0.417,0.25 1.646,0.979 1.646,0.313 1.646,0.313 1.396,0.313 false 1.052,2.813 1.438,2.375 true 2.104,2.823 1.719,2.385 true 0.698,0.958 1.135,1.354 0.438,0.396 10 false *1 2.583,0.698 2.958,1.135 0.375,0.438 10 false *2 1.24,0.24 1.74,0.813 0.5,0.573 10 false *3 0.427,1.854 0.833,2.281 0.406,0.427 10 false *a 1.979,2.833 2.563,3.25 0.583,0.417 10 false BFR+ 0.906,2.833 1.49,3.25 0.583,0.417 10 false BFR- 0.667,2.292 1.042,2.542 0.375,0.25 10 false M34 2.219,0.958 2.594,1.396 0.375,0.438 10 false A 1.906,0.958 2.281,1.396 0.375,0.438 10 false B 1.313,0.958 1.688,1.396 0.375,0.438 10 false C 1.01,0.958 1.385,1.396 0.375,0.438 10 false D
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Floor Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-2 (BFR+) - Body ground Always 1 MΩ or higher
M34-1 (BFR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR SIDE AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR SIDE AIRBAG SENSOR RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the floor side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B/85, B162C/85, B163B/86 and B163C/86 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B162B/85 or B162C/85 is output. A
DTC B163B/86 or B163C/86 is output. B
DTCs B162B/85, B162C/85, B163B/86 and B163C/86 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the floor side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C