Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B163B/86  Side Airbag Sensor Assembly No.2 Lost Communication (LH)  B163C/86  Side Airbag Sensor Assembly No.2 Initialization Error (LH)  


DESCRIPTION

The side collision sensor LH circuit (bus 2) consists of the airbag sensor assembly and floor side airbag sensor LH.

The floor side airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B163B/86 Side Airbag Sensor Assembly No.2 Lost Communication (LH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2)

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2).

·

Floor side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B163C/86 Side Airbag Sensor Assembly No.2 Initialization Error (LH) Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2)

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2).

·

Floor side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Floor side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B163B/86):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2) - - - ○ - -
Floor side airbag sensor LH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B163C/86):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 2) ○ - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 2) - ○ - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 2) - - ○ - - -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 2) - - - ○ - -
Floor side airbag sensor LH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C303969E31
5.302,2.885 6.948,3.531 1.646,0.646 10 false Airbag Sensor Assembly 5.302,2.719 6.844,2.927 1.542,0.208 10 false M2*1, M1*2 4.635,0.802 5.406,0.979 0.771,0.177 10 false 11*1, 21*2 4.646,1.771 5.417,1.969 0.771,0.198 10 false 12*1, 22*2 5.375,0.906 6.094,1.302 0.719,0.396 10 false BCL+ 5.375,1.875 6.094,2.271 0.719,0.396 10 false BCL- 1.417,0.906 2.135,1.302 0.719,0.396 10 false BFL+ 1.438,1.875 2.156,2.271 0.719,0.396 10 false BFL- 1.844,0.802 2.563,1.198 0.719,0.396 10 false 2 1.844,1.781 2.563,2.177 0.719,0.396 10 false 1 0.563,2.719 1.25,2.885 0.688,0.167 10 false M35 0.552,2.885 2.115,3.281 1.563,0.396 10 false Floor Side Airbag Sensor LH 3.083,3.031 4.75,3.281 1.667,0.25 10 false *1: w/o Dual-stage SRS 3.094,3.375 4.76,3.625 1.667,0.25 10 false *2: w/ Dual-stage SRS

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and floor side airbag sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and floor side airbag sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.

Using a service wire, connect terminals 21 (BCL+) and 22 (BCL-) of connector B.

C360607C02
1.25,1 1.667,1.25 0.417,0.25 4.417,1 4.833,1.25 0.417,0.25 4.167,3.417 4.583,3.667 0.417,0.25 1,3.417 1.417,3.667 0.417,0.25 2.333,1.583 1.969,1.323 true 1.583,1.583 1.844,1.323 true 5.167,1.5 5.385,1.208 true 5.75,1.5 5.521,1.208 true 5.417,3.917 5.177,3.563 true 4.75,3.917 4.948,3.573 true 2.25,3.917 1.969,3.583 true 1.5,3.917 1.729,3.573 true 1.917,2.771 1.917,2.521 false 5.135,2.552 5.135,2.302 false 1.917,1.667 1.917,1.583 false 5.438,1.625 5.438,1.479 false 1.094,2.396 1.406,2.552 0.313,0.156 10 false *1 5.938,2.417 6.25,2.573 0.313,0.156 10 false *2 1.844,2.792 2.156,2.948 0.313,0.156 10 false *3 1.854,1.646 2.167,1.802 0.313,0.156 10 false *4 1.188,0.677 1.5,0.833 0.313,0.156 10 false *a 4.198,3.177 4.51,3.333 0.313,0.156 10 false *b 4.438,0.677 4.75,0.833 0.313,0.156 10 false *a 1,3.146 1.313,3.302 0.313,0.156 10 false *b 4.313,2.177 4.625,2.333 0.313,0.156 10 false *1 2.719,2.417 3.031,2.573 0.313,0.156 10 false *2 5.073,2.573 5.385,2.729 0.313,0.156 10 false *3 5.365,1.635 5.677,1.792 0.313,0.156 10 false *4 1.26,1.583 1.74,1.823 0.479,0.24 10 false BCL+ 2.323,1.594 2.802,1.833 0.479,0.24 10 false BCL- 5.76,1.552 6.24,1.792 0.479,0.24 10 false BCL- 4.802,1.531 5.281,1.771 0.479,0.24 10 false BCL+ 0.271,0.188 0.75,0.427 0.479,0.24 12 false *A 3.938,0.188 4.417,0.427 0.479,0.24 12 false *B 1.365,1.031 1.667,1.25 0.302,0.219 10 false M2 4.531,1.031 4.833,1.25 0.302,0.219 10 false M1 1.385,2.375 1.594,2.583 0.208,0.208 10 false D 1.635,2.385 1.948,2.542 0.313,0.156 10 false C 2.115,2.385 2.427,2.542 0.313,0.156 10 false B 2.365,2.396 2.677,2.552 0.313,0.156 10 false A 5.583,2.167 5.896,2.323 0.313,0.156 10 false A 5.333,2.177 5.646,2.333 0.313,0.156 10 false B 4.854,2.177 5.167,2.333 0.313,0.156 10 false C 4.604,2.177 4.917,2.333 0.313,0.156 10 false D 1.177,3.927 1.656,4.167 0.479,0.24 10 false BFL- 2.24,3.948 2.719,4.188 0.479,0.24 10 false BFL+ 5.406,3.948 5.885,4.188 0.479,0.24 10 false BFL+ 4.469,3.938 4.948,4.177 0.479,0.24 10 false BFL- 4.25,3.448 4.729,3.688 0.479,0.24 10 false M35 1.083,3.458 1.563,3.698 0.479,0.24 10 false M35
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Floor Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Floor Side Airbag Sensor LH)


NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-2 (BFL+) - M35-1 (BFL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.

Measure the resistance according to the value(s) in the table below.

C360608C01
1.083,2.167 1.5,2.417 0.417,0.25 4.5,2.167 4.917,2.417 0.417,0.25 1.583,2.667 1.865,2.302 true 2.417,2.667 2.104,2.281 true 5.75,2.667 5.458,2.271 true 5,2.667 5.229,2.281 true 2.083,1.396 2.083,1.229 false 5.417,1.188 5.417,1.021 false 1,0.313 1.313,0.552 0.313,0.24 12 false *A 4.104,0.313 4.438,0.563 0.333,0.25 12 false *B 1.24,1.115 1.552,1.271 0.313,0.156 10 false *1 1.302,2.677 1.865,2.844 0.563,0.167 10 false BFL- 2.01,1.396 2.323,1.552 0.313,0.156 10 false *3 1.115,1.885 1.427,2.042 0.313,0.156 10 false *a 1.521,1.104 1.688,1.344 0.167,0.24 10 false D 4.573,0.885 4.885,1.042 0.313,0.156 10 false *1 2.854,1.115 3.167,1.271 0.313,0.156 10 false *2 6.198,1.104 6.51,1.26 0.313,0.156 10 false *2 4.469,1.865 4.781,2.021 0.313,0.156 10 false *a 1.76,1.104 1.927,1.344 0.167,0.24 10 false C 2.25,1.104 2.417,1.344 0.167,0.24 10 false B 5.865,0.885 6.031,1.125 0.167,0.24 10 false A 2.5,1.104 2.667,1.344 0.167,0.24 10 false A 5.615,0.896 5.781,1.135 0.167,0.24 10 false B 5.135,0.896 5.302,1.135 0.167,0.24 10 false C 4.875,0.896 5.042,1.135 0.167,0.24 10 false D 5.344,1.188 5.656,1.344 0.313,0.156 10 false *3 4.698,2.688 5.26,2.854 0.563,0.167 10 false BFL- 2.406,2.688 2.969,2.854 0.563,0.167 10 false BFL+ 5.729,2.708 6.292,2.875 0.563,0.167 10 false BFL+ 4.583,2.219 5.146,2.385 0.563,0.167 10 false M35 1.167,2.208 1.729,2.375 0.563,0.167 10 false M35
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Floor Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Floor Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M35-2 (BFL+) - M35-1 (BFL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.

Connect the cable to the negative (-) auxiliary battery terminal.

C360608C01
1.083,2.167 1.5,2.417 0.417,0.25 4.5,2.167 4.917,2.417 0.417,0.25 1.583,2.667 1.865,2.302 true 2.417,2.667 2.104,2.281 true 5.75,2.667 5.458,2.271 true 5,2.667 5.229,2.281 true 2.083,1.396 2.083,1.229 false 5.417,1.188 5.417,1.021 false 1,0.313 1.313,0.552 0.313,0.24 12 false *A 4.104,0.313 4.438,0.563 0.333,0.25 12 false *B 1.24,1.115 1.552,1.271 0.313,0.156 10 false *1 1.302,2.677 1.865,2.844 0.563,0.167 10 false BFL- 2.01,1.396 2.323,1.552 0.313,0.156 10 false *3 1.115,1.885 1.427,2.042 0.313,0.156 10 false *a 1.521,1.104 1.688,1.344 0.167,0.24 10 false D 4.573,0.885 4.885,1.042 0.313,0.156 10 false *1 2.854,1.115 3.167,1.271 0.313,0.156 10 false *2 6.198,1.104 6.51,1.26 0.313,0.156 10 false *2 4.469,1.865 4.781,2.021 0.313,0.156 10 false *a 1.76,1.104 1.927,1.344 0.167,0.24 10 false C 2.25,1.104 2.417,1.344 0.167,0.24 10 false B 5.865,0.885 6.031,1.125 0.167,0.24 10 false A 2.5,1.104 2.667,1.344 0.167,0.24 10 false A 5.615,0.896 5.781,1.135 0.167,0.24 10 false B 5.135,0.896 5.302,1.135 0.167,0.24 10 false C 4.875,0.896 5.042,1.135 0.167,0.24 10 false D 5.344,1.188 5.656,1.344 0.313,0.156 10 false *3 4.698,2.688 5.26,2.854 0.563,0.167 10 false BFL- 2.406,2.688 2.969,2.854 0.563,0.167 10 false BFL+ 5.729,2.708 6.292,2.875 0.563,0.167 10 false BFL+ 4.583,2.219 5.146,2.385 0.563,0.167 10 false M35 1.167,2.208 1.729,2.375 0.563,0.167 10 false M35
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Floor Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Floor Side Airbag Sensor LH)
- -



b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M35-2 (BFL+) - Body ground Power switch on (IG) Below 1 V
M35-1 (BFL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C360608C01
1.083,2.167 1.5,2.417 0.417,0.25 4.5,2.167 4.917,2.417 0.417,0.25 1.583,2.667 1.865,2.302 true 2.417,2.667 2.104,2.281 true 5.75,2.667 5.458,2.271 true 5,2.667 5.229,2.281 true 2.083,1.396 2.083,1.229 false 5.417,1.188 5.417,1.021 false 1,0.313 1.313,0.552 0.313,0.24 12 false *A 4.104,0.313 4.438,0.563 0.333,0.25 12 false *B 1.24,1.115 1.552,1.271 0.313,0.156 10 false *1 1.302,2.677 1.865,2.844 0.563,0.167 10 false BFL- 2.01,1.396 2.323,1.552 0.313,0.156 10 false *3 1.115,1.885 1.427,2.042 0.313,0.156 10 false *a 1.521,1.104 1.688,1.344 0.167,0.24 10 false D 4.573,0.885 4.885,1.042 0.313,0.156 10 false *1 2.854,1.115 3.167,1.271 0.313,0.156 10 false *2 6.198,1.104 6.51,1.26 0.313,0.156 10 false *2 4.469,1.865 4.781,2.021 0.313,0.156 10 false *a 1.76,1.104 1.927,1.344 0.167,0.24 10 false C 2.25,1.104 2.417,1.344 0.167,0.24 10 false B 5.865,0.885 6.031,1.125 0.167,0.24 10 false A 2.5,1.104 2.667,1.344 0.167,0.24 10 false A 5.615,0.896 5.781,1.135 0.167,0.24 10 false B 5.135,0.896 5.302,1.135 0.167,0.24 10 false C 4.875,0.896 5.042,1.135 0.167,0.24 10 false D 5.344,1.188 5.656,1.344 0.313,0.156 10 false *3 4.698,2.688 5.26,2.854 0.563,0.167 10 false BFL- 2.406,2.688 2.969,2.854 0.563,0.167 10 false BFL+ 5.729,2.708 6.292,2.875 0.563,0.167 10 false BFL+ 4.583,2.219 5.146,2.385 0.563,0.167 10 false M35 1.167,2.208 1.729,2.375 0.563,0.167 10 false M35
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Floor Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Floor Side Airbag Sensor LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
M35-2 (BFL+) - Body ground Always 1 MΩ or higher
M35-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR SIDE AIRBAG SENSOR LH
a.
C360613C02
0.177,0.125 0.51,0.375 0.333,0.25 12 false *A 0.26,1.594 0.594,1.833 0.333,0.24 12 false *B 0.458,0.729 0.771,0.885 0.313,0.156 10 false *1 2.615,0.75 2.927,0.906 0.313,0.156 10 false *2 0.469,2.208 0.781,2.365 0.313,0.156 10 false *1 2.625,2.51 2.938,2.667 0.313,0.156 10 false *2 0.844,0.74 1.073,0.906 0.229,0.167 10 false D 1,0.74 1.229,0.906 0.229,0.167 10 false C 2.063,0.729 2.292,0.896 0.229,0.167 10 false B 2.208,0.729 2.438,0.896 0.229,0.167 10 false A 2.219,2.219 2.448,2.385 0.229,0.167 10 false A 2.052,2.219 2.281,2.385 0.229,0.167 10 false B 1,2.208 1.229,2.375 0.229,0.167 10 false C 0.844,2.208 1.073,2.375 0.229,0.167 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the floor side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B162B/85, B162C/85, B163B/86 and B163C/86 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B163B/86 or B163C/86 is output. A
DTC B162B/85 or B162C/85 is output. B
DTCs B162B/85, B162C/85, B163B/86 and B163C/86 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the floor side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C