The airbag cut off switch circuit consists of the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
The instrument panel passenger without door airbag assembly can be optionally deactivated via this circuit by turning the airbag cut off switch cylinder sub-assembly to the OFF position.
If the instrument panel passenger without door airbag assembly is deactivated, the passenger airbag ON/OFF indicator ("OFF") comes on to inform the driver.
DTC B1651/33 is stored when a malfunction is detected in the airbag cut off switch circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1651/33 | Manual Cut off Switch Trouble | Any of the following conditions is met:
·
The airbag sensor assembly detects a line short, in the airbag cut off switch circuit. ·
The airbag sensor assembly detects a short to ground in the airbag cut off switch circuit. ·
The airbag sensor assembly detects a short to B+ in the airbag cut off switch circuit. ·
The airbag sensor assembly detects an open in the airbag cut off switch circuit. ·
Airbag cut off switch cylinder sub-assembly malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Airbag cut off switch cylinder sub-assembly ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||||||
|---|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Power switch on (IG) | ○ | ○ | ○ | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short, in the airbag cut off switch circuit | ○ | - | - | - | - | - |
| The airbag sensor assembly detects a short to ground in the airbag cut off switch circuit | - | ○ | - | - | - | - | |
| The airbag sensor assembly detects a short to B+ in the airbag cut off switch circuit | - | - | ○ | - | - | - | |
| The airbag sensor assembly detects an open in the airbag cut off switch circuit | - | - | - | ○ | - | - | |
| Airbag cut off switch cylinder sub-assembly malfunction | - | - | - | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | - | - | - | ○ | |
| Detection Time | - | - | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Terminals F70-11 (MSW+) and F70-12 (MSW-) of the instrument panel wire in this circuit have an activation prevention mechanism.
This mechanism can be used to check for an open circuit in the wire harness. When performing other checks (check for short, short to ground or short to B+), this mechanism should be released.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - F64-1 (PMC-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - F64-1 (PMC-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - Body ground | Power switch on (IG) | Below 1 V |
| F64-1 (PMC-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F64-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| F64-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (PMC+) - 1 (PMC-) | Cut off switch in ON position | 360 to 440 Ω |
| 2 (PMC+) - 1 (PMC-) | Cut off switch in OFF position | 90 to 110 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Airbag Cut Off Switch Cylinder Sub-assembly |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1651/33 is not output.
Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG