Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger without door airbag assembly.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit.

·

Passenger airbag ON/OFF indicator malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Instrument panel junction block assembly

·

Passenger airbag ON/OFF indicator (Clock assembly)

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit - - ○ - - -
The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit - - - ○ - -
Passenger airbag ON/OFF indicator malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C360622E04
1.042,0.542 1.656,0.74 0.615,0.198 10 false PAON 1.104,1 1.719,1.198 0.615,0.198 10 false P-AB 1.323,1.823 1.938,2.021 0.615,0.198 10 false B 0.177,2.917 0.792,3.115 0.615,0.198 10 false F81 0.177,3.104 2.396,3.479 2.219,0.375 10 false Passenger Airbag ON/OFF Indicator (Clock Assembly) 2.281,1.969 3.469,2.188 1.188,0.219 10 false ECU-DCC NO. 2 2.344,1.177 2.958,1.375 0.615,0.198 10 false 3A 2.344,1.333 5.208,1.573 2.865,0.24 10 false Instrument Panel Junction Block Assembly 2.76,0.427 3,0.615 0.24,0.188 10 false 29 2.75,0.875 2.99,1.063 0.24,0.188 10 false 51 4.292,0.438 4.531,0.625 0.24,0.188 10 false 8 4.292,0.885 4.531,1.073 0.24,0.188 10 false 46 5.24,0.427 5.479,0.615 0.24,0.188 10 false 23 5.25,0.885 5.49,1.073 0.24,0.188 10 false 17 5.24,1.719 5.479,1.906 0.24,0.188 10 false 25 5.24,2.167 5.479,2.354 0.24,0.188 10 false 26 5.5,1.833 5.74,2.021 0.24,0.188 10 false E1 5.521,2.281 5.76,2.469 0.24,0.188 10 false E2 5.5,0.542 6.115,0.74 0.615,0.198 10 false PAON 5.51,1 6.125,1.198 0.615,0.198 10 false P-AB 5.427,2.917 5.833,3.146 0.406,0.229 10 false F70 5.417,3.104 7.01,3.365 1.594,0.26 10 false Airbag Sensor Assembly 2.896,2.552 4.302,2.854 1.406,0.302 10 false from Auxiliary Battery 1.573,0.438 1.813,0.625 0.24,0.188 10 false 4 1.563,0.896 1.802,1.083 0.24,0.188 10 false 3 1.563,1.719 1.802,1.906 0.24,0.188 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the power switch on (IG).


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
Passenger airbag ON/OFF indicator illumination is always on. A
Passenger airbag ON/OFF indicator illumination is always off. B



A

2.CHECK CONNECTORS

B

13.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Connect the connector to the passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK WIRE HARNESS (OPEN)
4.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Connect the connector to the airbag sensor assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK WIRE HARNESS (OPEN)
a.
C369271C02
0.333,0.667 0.75,0.917 0.417,0.25 0.333,3.5 0.75,3.75 0.417,0.25 1.542,1.531 1.542,1.365 false 0.917,1.417 1.26,1.073 true 2,1.417 1.729,0.844 true 1.833,2.833 1.833,2.167 false 1.615,2.5 1.833,2.5 false 0.75,4 1.302,3.813 true 0.74,4.229 1.448,3.833 true 0.281,2.104 0.594,2.26 0.313,0.156 10 false *1 2.854,2.135 3.167,2.292 0.313,0.156 10 false *2 0.292,2.719 0.604,2.875 0.313,0.156 10 false *3 1.75,2.875 2.063,3.031 0.313,0.156 10 false *4 1.469,1.573 1.781,1.729 0.313,0.156 10 false *5 0.333,0.333 0.646,0.49 0.313,0.156 10 false *a 0.313,3.292 0.625,3.448 0.313,0.156 10 false *b 0.427,0.708 0.885,0.906 0.458,0.198 10 false F70 2.573,2.104 2.729,2.302 0.156,0.198 10 false A 2.229,2.104 2.385,2.302 0.156,0.198 10 false B 0.708,2.104 0.865,2.302 0.156,0.198 10 false C 0.542,2.104 0.698,2.302 0.156,0.198 10 false D 0.875,2.708 1.031,2.906 0.156,0.198 10 false E 0.542,2.708 0.698,2.906 0.156,0.198 10 false F 0.656,1.458 1.271,1.656 0.615,0.198 10 false PAON 1.896,1.458 2.51,1.656 0.615,0.198 10 false P-AB 0.427,3.542 0.885,3.74 0.458,0.198 10 false F81 0.292,4.188 0.906,4.385 0.615,0.198 10 false PAON 0.365,3.896 0.979,4.094 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the passenger airbag ON/OFF indicator (clock assembly).


d.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (SHORT)

NG

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
6.CHECK WIRE HARNESS (SHORT)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
7.CHECK WIRE HARNESS (SHORT TO B+)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-4 (PAON) - Body ground Power switch on (IG) Below 1 V
F81-3 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
8.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - Body ground Always 1 MΩ or higher
F81-3 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE PASSENGER AIRBAG ON/OFF INDICATOR (CLOCK ASSEMBLY)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-8 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-29 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-46 (P-AB) - Body ground Power switch on (IG) Below 1 V
3A-51 (P-AB) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C369274C01
1.083,3.333 1.5,3.583 0.417,0.25 1.25,0.333 1.667,0.583 0.417,0.25 2.26,4.177 2.26,4.01 false 1.667,4.083 2,3.719 true 2.833,4.083 2.448,3.469 true 1.833,2.75 1.833,2.25 false 1.635,2.5 1.833,2.5 false 1.583,1.5 1.802,1.177 true 1.917,0.854 2.25,0.5 true 0.313,2.188 0.625,2.344 0.313,0.156 10 false *1 2.958,2.208 3.271,2.365 0.313,0.156 10 false *2 0.313,2.729 0.625,2.885 0.313,0.156 10 false *3 1.76,2.792 2.073,2.948 0.313,0.156 10 false *4 2.177,4.208 2.49,4.365 0.313,0.156 10 false *5 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a 1.083,3.083 1.396,3.24 0.313,0.156 10 false *b 1.375,0.375 1.688,0.573 0.313,0.198 10 false 3A 2.302,0.375 2.917,0.573 0.615,0.198 10 false PAON 1.302,1.542 1.917,1.74 0.615,0.198 10 false P-AB 2.583,2.188 2.74,2.385 0.156,0.198 10 false A 2.25,2.188 2.406,2.385 0.156,0.198 10 false B 0.896,2.188 1.052,2.385 0.156,0.198 10 false C 0.563,2.188 0.719,2.385 0.156,0.198 10 false D 0.896,2.729 1.052,2.927 0.156,0.198 10 false E 0.563,2.729 0.719,2.927 0.156,0.198 10 false F 1.177,3.375 1.635,3.573 0.458,0.198 10 false F70 1.344,4.125 1.958,4.323 0.615,0.198 10 false PAON 2.729,4.125 3.344,4.323 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connector from the instrument panel junction block assembly.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.
C369275C02
0.333,3.583 0.75,3.833 0.417,0.25 1.25,0.167 1.667,0.417 0.417,0.25 1.521,4.375 1.75,4.417 false 0.75,4.25 1.323,3.813 true 2.25,4.333 1.521,3.802 true 1.833,2.833 1.833,2.083 false 1.625,2.333 1.833,2.333 false 2.333,1.333 2.479,0.99 true 2.385,0.792 2.583,0.333 true 0.292,2 0.604,2.156 0.313,0.156 10 false *1 2.865,2 3.177,2.156 0.313,0.156 10 false *2 0.292,2.542 0.604,2.698 0.313,0.156 10 false *3 1.75,2.875 2.063,3.031 0.313,0.156 10 false *4 1.792,4.333 2.104,4.49 0.313,0.156 10 false *5 0.417,0.167 0.729,0.323 0.313,0.156 10 false *a 0.365,3.229 0.677,3.385 0.313,0.156 10 false *b 1.375,0.208 1.688,0.406 0.313,0.198 10 false 3A 2.25,4.365 2.865,4.563 0.615,0.198 10 false PAON 1.969,1.333 2.583,1.531 0.615,0.198 10 false P-AB 0.563,2.542 0.719,2.74 0.156,0.198 10 false F 2.594,2.01 2.75,2.208 0.156,0.198 10 false A 2.25,2.01 2.406,2.208 0.156,0.198 10 false B 0.896,2.542 1.052,2.74 0.156,0.198 10 false E 0.896,2.01 1.052,2.208 0.156,0.198 10 false C 0.563,2.01 0.719,2.208 0.156,0.198 10 false D 0.427,3.625 0.885,3.823 0.458,0.198 10 false F81 2.625,0.188 3.24,0.385 0.615,0.198 10 false PAON 0.479,4.281 1.094,4.479 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Using a service wire, connect terminals 3 (P-AB) and 4 (PAON) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

13.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK WIRE HARNESS (OPEN)
a.
C369276C02
0.417,3.5 0.833,3.75 0.417,0.25 0.417,0.667 0.833,0.917 0.417,0.25 1.552,1.531 1.552,1.365 false 1,1.417 1.292,1.073 true 2,1.417 1.74,0.844 true 1.833,2.917 1.833,2.167 false 1.625,2.5 1.833,2.5 false 0.833,4 1.323,3.823 true 0.75,4.25 1.458,3.823 true 0.302,2.125 0.615,2.281 0.313,0.156 10 false *1 2.896,2.104 3.208,2.26 0.313,0.156 10 false *2 0.302,2.719 0.615,2.875 0.313,0.156 10 false *3 1.76,2.979 2.073,3.135 0.313,0.156 10 false *4 1.479,1.573 1.792,1.729 0.313,0.156 10 false *5 0.417,0.333 0.729,0.49 0.313,0.156 10 false *a 0.417,3.25 0.729,3.406 0.313,0.156 10 false *b 0.51,0.708 0.969,0.906 0.458,0.198 10 false F70 0.5,3.542 0.958,3.74 0.458,0.198 10 false F81 0.615,1.448 1.229,1.646 0.615,0.198 10 false PAON 2.01,1.448 2.625,1.646 0.615,0.198 10 false P-AB 2.594,2.104 2.75,2.302 0.156,0.198 10 false A 2.25,2.104 2.406,2.302 0.156,0.198 10 false B 0.729,2.104 0.885,2.302 0.156,0.198 10 false C 0.552,2.104 0.708,2.302 0.156,0.198 10 false D 0.896,2.708 1.052,2.906 0.156,0.198 10 false E 0.563,2.708 0.719,2.906 0.156,0.198 10 false F 0.313,4.177 0.927,4.375 0.615,0.198 10 false PAON 0.448,3.917 1.063,4.115 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the connector to the instrument panel junction block assembly.


b.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK WIRE HARNESS (SHORT)

NG

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
15.CHECK WIRE HARNESS (SHORT)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK WIRE HARNESS (SHORT TO B+)

NG

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
16.CHECK WIRE HARNESS (SHORT TO B+)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-4 (PAON) - Body ground Power switch on (IG) Below 1 V
F81-3 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

17.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
17.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C369272C03
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.667 1.438,3.156 true 0.667,3.417 1.281,3.146 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.219,3.625 0.833,3.823 0.615,0.198 10 false PAON 0.271,3.333 0.885,3.531 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - Body ground Always 1 MΩ or higher
F81-3 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
C369272C04
0.25,2.833 0.667,3.083 0.417,0.25 1.833,2.083 1.833,1.313 false 1.635,1.667 1.833,1.667 false 0.667,3.5 1.875,3.156 true 0.156,1.26 0.469,1.417 0.313,0.156 10 false *1 3.01,1.271 3.323,1.427 0.313,0.156 10 false *2 0.167,1.927 0.479,2.083 0.313,0.156 10 false *3 1.75,2.125 2.063,2.281 0.313,0.156 10 false *4 0.25,2.583 0.563,2.74 0.313,0.156 10 false *a 2.698,1.25 2.854,1.448 0.156,0.198 10 false A 2.323,1.25 2.479,1.448 0.156,0.198 10 false B 0.635,1.25 0.792,1.448 0.156,0.198 10 false C 0.438,1.25 0.594,1.448 0.156,0.198 10 false D 0.813,1.927 0.969,2.125 0.156,0.198 10 false E 0.448,1.927 0.604,2.125 0.156,0.198 10 false F 0.354,2.865 0.719,3.073 0.365,0.208 10 false F81 0.469,3.438 0.875,3.635 0.406,0.198 10 false B
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-7 (B) - Body ground Power switch off 11 to 14 V



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR AUXILIARY BATTERY

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C369277C01
1,2.917 1.417,3.167 0.417,0.25 1.75,2.083 1.75,1.219 false 1.51,1.583 1.75,1.583 false 1.833,3.583 2.01,3.333 true 2.667,3.583 2.469,3.083 true 0.229,1.167 0.542,1.323 0.313,0.156 10 false *1 2.885,1.167 3.198,1.323 0.313,0.156 10 false *2 0.229,1.844 0.542,2 0.313,0.156 10 false *3 1.667,2.135 1.979,2.292 0.313,0.156 10 false *4 1,2.5 1.313,2.656 0.313,0.156 10 false *a 2.583,1.156 2.74,1.354 0.156,0.198 10 false A 2.198,1.156 2.354,1.354 0.156,0.198 10 false B 0.708,1.156 0.865,1.354 0.156,0.198 10 false C 0.51,1.156 0.667,1.354 0.156,0.198 10 false D 0.708,1.833 0.865,2.031 0.156,0.198 10 false E 0.51,1.833 0.667,2.031 0.156,0.198 10 false F 1.094,2.958 1.552,3.156 0.458,0.198 10 false F70 1.458,3.625 2.073,3.823 0.615,0.198 10 false PAON 2.677,3.625 3.292,3.823 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the passenger airbag ON/OFF indicator (clock assembly).


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:
Terminal Connection Switch Condition Specified Condition
F70-23 (PAON) - Body ground Power switch on (IG) "ON" comes on
F70-17 (P-AB) - Body ground Power switch on (IG) "OFF" comes on



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

20.CHECK DTC

NG

REPLACE PASSENGER AIRBAG ON/OFF INDICATOR (CLOCK ASSEMBLY)

20.CHECK DTC
a.
C284134C01
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-8 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-29 (PAON) - Body ground Power switch on (IG) Below 1 V
3A-46 (P-AB) - Body ground Power switch on (IG) Below 1 V
3A-51 (P-AB) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C369273C01
1.25,0.833 1.667,1.083 0.417,0.25 1.833,4 1.833,3.052 false 1.615,3.417 1.833,3.417 false 1.885,1.385 2.083,0.917 true 1.667,2.167 1.802,1.771 true 2.667,2.167 2.563,1.771 true 2.479,1.552 2.75,1 true 0.156,3.01 0.469,3.167 0.313,0.156 10 false *1 2.99,3 3.302,3.156 0.313,0.156 10 false *2 0.156,3.604 0.469,3.76 0.313,0.156 10 false *3 1.75,4.042 2.063,4.198 0.313,0.156 10 false *4 0.25,0.833 0.563,0.99 0.313,0.156 10 false *a 2.688,2.99 2.844,3.188 0.156,0.198 10 false A 2.313,2.99 2.469,3.188 0.156,0.198 10 false B 0.802,2.99 0.958,3.188 0.156,0.198 10 false C 0.427,2.99 0.583,3.188 0.156,0.198 10 false D 0.802,3.594 0.958,3.792 0.156,0.198 10 false E 0.427,3.594 0.583,3.792 0.156,0.198 10 false F 1.375,0.865 1.688,1.063 0.313,0.198 10 false 3A 1.385,2.208 1.813,2.385 0.427,0.177 10 false P-AB 2.646,2.198 3.073,2.375 0.427,0.177 10 false P-AB 2.125,0.802 2.615,1 0.49,0.198 10 false PAON 2.792,0.885 3.281,1.083 0.49,0.198 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C369274C01
1.083,3.333 1.5,3.583 0.417,0.25 1.25,0.333 1.667,0.583 0.417,0.25 2.26,4.177 2.26,4.01 false 1.667,4.083 2,3.719 true 2.833,4.083 2.448,3.469 true 1.833,2.75 1.833,2.25 false 1.635,2.5 1.833,2.5 false 1.583,1.5 1.802,1.177 true 1.917,0.854 2.25,0.5 true 0.313,2.188 0.625,2.344 0.313,0.156 10 false *1 2.958,2.208 3.271,2.365 0.313,0.156 10 false *2 0.313,2.729 0.625,2.885 0.313,0.156 10 false *3 1.76,2.792 2.073,2.948 0.313,0.156 10 false *4 2.177,4.208 2.49,4.365 0.313,0.156 10 false *5 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a 1.083,3.083 1.396,3.24 0.313,0.156 10 false *b 1.375,0.375 1.688,0.573 0.313,0.198 10 false 3A 2.302,0.375 2.917,0.573 0.615,0.198 10 false PAON 1.302,1.542 1.917,1.74 0.615,0.198 10 false P-AB 2.583,2.188 2.74,2.385 0.156,0.198 10 false A 2.25,2.188 2.406,2.385 0.156,0.198 10 false B 0.896,2.188 1.052,2.385 0.156,0.198 10 false C 0.563,2.188 0.719,2.385 0.156,0.198 10 false D 0.896,2.729 1.052,2.927 0.156,0.198 10 false E 0.563,2.729 0.719,2.927 0.156,0.198 10 false F 1.177,3.375 1.635,3.573 0.458,0.198 10 false F70 1.344,4.125 1.958,4.323 0.615,0.198 10 false PAON 2.729,4.125 3.344,4.323 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connector from the instrument panel junction block assembly.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.
C369275C02
0.333,3.583 0.75,3.833 0.417,0.25 1.25,0.167 1.667,0.417 0.417,0.25 1.521,4.375 1.75,4.417 false 0.75,4.25 1.323,3.813 true 2.25,4.333 1.521,3.802 true 1.833,2.833 1.833,2.083 false 1.625,2.333 1.833,2.333 false 2.333,1.333 2.479,0.99 true 2.385,0.792 2.583,0.333 true 0.292,2 0.604,2.156 0.313,0.156 10 false *1 2.865,2 3.177,2.156 0.313,0.156 10 false *2 0.292,2.542 0.604,2.698 0.313,0.156 10 false *3 1.75,2.875 2.063,3.031 0.313,0.156 10 false *4 1.792,4.333 2.104,4.49 0.313,0.156 10 false *5 0.417,0.167 0.729,0.323 0.313,0.156 10 false *a 0.365,3.229 0.677,3.385 0.313,0.156 10 false *b 1.375,0.208 1.688,0.406 0.313,0.198 10 false 3A 2.25,4.365 2.865,4.563 0.615,0.198 10 false PAON 1.969,1.333 2.583,1.531 0.615,0.198 10 false P-AB 0.563,2.542 0.719,2.74 0.156,0.198 10 false F 2.594,2.01 2.75,2.208 0.156,0.198 10 false A 2.25,2.01 2.406,2.208 0.156,0.198 10 false B 0.896,2.542 1.052,2.74 0.156,0.198 10 false E 0.896,2.01 1.052,2.208 0.156,0.198 10 false C 0.563,2.01 0.719,2.208 0.156,0.198 10 false D 0.427,3.625 0.885,3.823 0.458,0.198 10 false F81 2.625,0.188 3.24,0.385 0.615,0.198 10 false PAON 0.479,4.281 1.094,4.479 0.615,0.198 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Using a service wire, connect terminals 3 (P-AB) and 4 (PAON) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL WIRE