Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835/58  Short in Curtain Shield Squib LH Circuit  B1836/58  Open in Curtain Shield Squib LH Circuit  B1837/58  Short to GND in Curtain Shield Squib LH Circuit  B1838/58  Short to B+ in Curtain Shield Squib LH Circuit  


DESCRIPTION

The curtain shield squib LH circuit consists of the airbag sensor assembly and curtain shield airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1835/58 Short in Curtain Shield Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the curtain shield squib LH circuit during the primary check.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield squib LH (Curtain shield airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1836/58 Open in Curtain Shield Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects an open in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield squib LH (Curtain shield airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1837/58 Short to GND in Curtain Shield Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to ground in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield squib LH (Curtain shield airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1838/58 Short to B+ in Curtain Shield Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to B+ in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield squib LH (Curtain shield airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode

DTC Detection Conditions (B1835/58):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the curtain shield squib LH circuit during the primary check ○ - -
Curtain shield squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1836/58):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the curtain shield squib LH circuit ○ - -
Curtain shield squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1837/58):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to ground in the curtain shield squib LH circuit ○ - -
Curtain shield squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1838/58):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to B+ in the curtain shield squib LH circuit ○ - -
Curtain shield squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

w/o Dual-stage SRS


C370614E03
2.427,1.063 2.583,1.26 0.156,0.198 10 false 1 2.427,1.906 2.583,2.104 0.156,0.198 10 false 2 4.51,1.073 4.667,1.271 0.156,0.198 10 false 7 4.521,1.896 4.76,2.083 0.24,0.188 10 false 6 4.74,1.156 5.208,1.354 0.469,0.198 10 false ICL+ 4.729,2 5.198,2.198 0.469,0.198 10 false ICL- 2.031,1.896 2.5,2.094 0.469,0.198 10 false ICL- 2,1.063 2.469,1.26 0.469,0.198 10 false ICL+ 0.594,2.51 1.063,2.708 0.469,0.198 10 false M25 4.75,3.031 5.219,3.229 0.469,0.198 10 false M2 4.75,3.219 6.49,3.448 1.74,0.229 10 false Airbag Sensor Assembly 0.583,2.667 2.594,3.083 2.01,0.417 10 false Curtain Shield Squib LH (Curtain Shield Airbag Assembly LH)


w/ Dual-stage SRS


C370614E04
2.427,1.063 2.583,1.26 0.156,0.198 10 false 1 2.427,1.906 2.583,2.104 0.156,0.198 10 false 2 4.51,1.063 4.667,1.26 0.156,0.198 10 false 4 4.521,1.896 4.76,2.083 0.24,0.188 10 false 3 4.74,1.156 5.208,1.354 0.469,0.198 10 false ICL+ 4.729,2 5.198,2.198 0.469,0.198 10 false ICL- 2.031,1.896 2.5,2.094 0.469,0.198 10 false ICL- 2,1.063 2.469,1.26 0.469,0.198 10 false ICL+ 0.594,2.51 1.063,2.708 0.469,0.198 10 false M25 4.75,3.031 5.219,3.229 0.469,0.198 10 false M1 4.75,3.219 6.49,3.448 1.74,0.229 10 false Airbag Sensor Assembly 0.583,2.667 2.594,3.083 2.01,0.417 10 false Curtain Shield Squib LH (Curtain Shield Airbag Assembly LH)


CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C284699C02
0.49,1.219 0.49,1.719 false 0.49,3.51 0.49,4.01 false 1.344,1.063 1.344,0.604 1.344,0.604 1.479,0.604 false 1.344,3.365 1.344,2.906 1.344,2.906 1.479,2.906 false 0.125,0.125 0.5,0.365 0.375,0.24 10 false *A 0.135,2.438 0.51,2.677 0.375,0.24 10 false *B 0.396,1.74 0.719,1.948 0.323,0.208 10 false *1 2.427,1.063 2.74,1.26 0.313,0.198 10 false *2 1.521,0.521 1.833,0.719 0.313,0.198 10 false *3 0.406,4.031 0.719,4.229 0.313,0.198 10 false *1 2.427,3.667 2.74,3.865 0.313,0.198 10 false *2 1.521,2.823 1.833,3.021 0.313,0.198 10 false *3 2,1.063 2.156,1.26 0.156,0.198 10 false A 1.594,1.063 1.75,1.26 0.156,0.198 10 false B 1.021,1.063 1.177,1.26 0.156,0.198 10 false C 0.615,1.063 0.771,1.26 0.156,0.198 10 false D 2,3.354 2.156,3.552 0.156,0.198 10 false A 1.594,3.354 1.75,3.552 0.156,0.198 10 false B 1.021,3.354 1.177,3.552 0.156,0.198 10 false C 0.615,3.354 0.771,3.552 0.156,0.198 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the curtain shield airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH
a.

Connect the connector to the airbag sensor assembly.

C348761C03
0.823,1.667 1.188,1.906 0.365,0.24 4.406,1.667 4.771,1.906 0.365,0.24 2.021,1.823 2.188,1.823 false 5.615,1.823 5.781,1.823 false 0.927,0.917 0.927,0.667 false 4.51,0.667 4.51,0.417 false 0.5,0.083 1.083,0.417 0.583,0.333 10 false *A 4.01,0.083 4.656,0.406 0.646,0.323 10 false *B 0.865,0.927 1.281,1.26 0.417,0.333 10 false *1 2.354,0.531 2.75,0.771 0.396,0.24 10 false *2 0.75,1.333 1.25,1.667 0.5,0.333 10 false *a 4.448,0.688 4.865,1.021 0.417,0.333 10 false *1 5.938,0.531 6.333,0.771 0.396,0.24 10 false *2 4.417,1.333 4.917,1.667 0.5,0.333 10 false *a 0.875,1.698 1.375,2.031 0.5,0.333 10 false M25 2.229,1.74 2.729,2.073 0.5,0.333 10 false SST 5.823,1.74 6.323,2.073 0.5,0.333 10 false SST 4.458,1.698 4.958,2.031 0.5,0.333 10 false M25 5.573,0.281 5.969,0.521 0.396,0.24 10 false A 5.438,0.281 5.833,0.521 0.396,0.24 10 false B 4.948,0.281 5.344,0.521 0.396,0.24 10 false C 4.604,0.281 5,0.521 0.396,0.24 10 false D 1.99,0.542 2.385,0.781 0.396,0.24 10 false A 1.854,0.542 2.25,0.781 0.396,0.24 10 false B 1.365,0.542 1.76,0.781 0.396,0.24 10 false C 1.01,0.542 1.406,0.781 0.396,0.24 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Curtain Shield Airbag Assembly LH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)
- -



b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the curtain shield airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.

Disconnect the floor wire from the airbag sensor assembly.

C348762C03
1.042,1.802 1.396,2.031 0.354,0.229 4.625,1.802 4.979,2.031 0.354,0.229 1.917,1.729 2.229,1.49 true 1.823,1.74 1.542,1.479 true 5.51,1.729 5.823,1.49 true 5.406,1.74 5.125,1.479 true 1.677,0.896 1.51,0.896 1.51,0.896 1.51,0.656 false 0.771,0.906 0.771,0.667 false 4.354,0.656 4.354,0.417 false 5.25,0.646 5.083,0.646 5.083,0.646 5.083,0.406 false 0.458,0.083 0.938,0.406 0.479,0.323 10 false *A 3.927,0.083 4.323,0.406 0.396,0.323 10 false *B 0.708,0.917 1.104,1.24 0.396,0.323 10 false *1 2.417,0.51 2.813,0.833 0.396,0.323 10 false *2 0.865,1.333 1.26,1.667 0.396,0.333 10 false *a 4.292,0.677 4.688,1 0.396,0.323 10 false *1 6,0.531 6.396,0.854 0.396,0.323 10 false *2 1.719,0.823 2.281,1.073 0.563,0.25 10 false *3 5.281,0.563 5.677,0.885 0.396,0.323 10 false *3 4.448,1.323 4.76,1.646 0.313,0.323 10 false *a 1.094,1.833 1.49,2.167 0.396,0.333 10 false M25 2.26,1.417 2.656,1.75 0.396,0.333 10 false ICL- 1.229,1.417 1.625,1.75 0.396,0.333 10 false ICL+ 4.677,1.833 5.073,2.167 0.396,0.333 10 false M25 5.865,1.417 6.26,1.75 0.396,0.333 10 false ICL- 4.802,1.417 5.198,1.75 0.396,0.333 10 false ICL+ 5.635,0.281 6.031,0.604 0.396,0.323 10 false A 5.281,0.281 5.677,0.604 0.396,0.323 10 false B 4.802,0.281 5.198,0.604 0.396,0.323 10 false C 4.448,0.281 4.844,0.604 0.396,0.323 10 false D 2.052,0.531 2.448,0.854 0.396,0.323 10 false A 1.708,0.531 2.104,0.854 0.396,0.323 10 false B 1.219,0.531 1.615,0.854 0.396,0.323 10 false C 0.865,0.531 1.26,0.854 0.396,0.323 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Curtain Shield Airbag Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)
- -



b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M25-1 (ICL+) - Body ground Power switch on (IG) Below 1 V
M25-2 (ICL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (ICL+) - M25-2 (ICL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (ICL+) - Body ground Always 1 MΩ or higher
M25-2 (ICL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (ICL+) - M25-2 (ICL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C284702C02
0.781,1.26 0.781,1.667 false 0.781,3.302 0.781,3.708 false 0.125,0.135 0.5,0.375 0.375,0.24 10 false *A 0.115,2.281 0.49,2.521 0.375,0.24 10 false *B 0.688,1.688 1,1.885 0.313,0.198 10 false *1 0.688,3.74 1,3.938 0.313,0.198 10 false *1 2.135,1.115 2.448,1.313 0.313,0.198 10 false *2 2.146,3.458 2.458,3.656 0.313,0.198 10 false *2 1.729,1.115 1.885,1.313 0.156,0.198 10 false A 1.563,1.115 1.719,1.313 0.156,0.198 10 false B 1.063,1.115 1.219,1.313 0.156,0.198 10 false C 0.906,1.115 1.063,1.313 0.156,0.198 10 false D 1.729,3.146 1.885,3.344 0.156,0.198 10 false A 1.563,3.146 1.719,3.344 0.156,0.198 10 false B 1.063,3.146 1.219,3.344 0.156,0.198 10 false C 0.906,3.146 1.063,3.344 0.156,0.198 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the curtain shield airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG